- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Auto Port Configuration Steps in 11.31
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 10:32 PM
тАО08-12-2009 10:32 PM
I need to create auto port configuration on a 11.31 Server.
Lan50 and Lan51 are lan cards and I need to create a autoport configuration lan900 as a failover group.
Then assign a IP address
IP_ADDRESS=35.80.66.1
SUBNET_MASK=255.255.240.0
Please provide me the list of commands
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 10:42 PM
тАО08-12-2009 10:42 PM
Re: Auto Port Configuration Steps in 11.31
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-12-2009 11:16 PM
тАО08-12-2009 11:16 PM
SolutionStep by step commands are documented here.
http://book.soundonair.ru/hall2/ch15lev1sec14.html
Ganesh.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2009 05:12 AM
тАО08-20-2009 05:12 AM
Re: Auto Port Configuration Steps in 11.31
Thanks for the link.
I need to create a lan900 as a failover group for lan50,53
I cannot understand the set of steps to use to assign an IP to lan900 and thn run lanapplyconf.
Sagar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО08-20-2009 01:01 PM
тАО08-20-2009 01:01 PM
Re: Auto Port Configuration Steps in 11.31
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2009 04:08 AM
тАО09-02-2009 04:08 AM
Re: Auto Port Configuration Steps in 11.31
In the /etc/rc.config.d/netconf
I have an entry for lan50
INTERFACE_NAME[0]="lan50"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
Now I have created lan900 with lan50 lan51.
So Now I have assign the IP address to lan900
I am using the sam eIp currently assigned to lan50.
What modifications I need to make to the /etc/rc.config.d/netconf file
Remove the entries for lan50 and lan51 and make an entry for lan900 as below
INTERFACE_NAME[0]="lan900"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-02-2009 04:17 AM
тАО09-02-2009 04:17 AM
Re: Auto Port Configuration Steps in 11.31
In the /etc/rc.config.d/netconf
I have an entry for lan50
INTERFACE_NAME[0]="lan50"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
Now I have created lan900 with lan50 lan51.
So Now I have assign the IP address to lan900
I am using the sam eIp currently assigned to lan50.
What modifications I need to make to the /etc/rc.config.d/netconf file
Remove the entries for lan50 and lan51 and make an entry for lan900 as below
INTERFACE_NAME[0]="lan900"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
#==========================================================
an example from my server :
INTERFACE_NAME[0]="lan900"
IP_ADDRESS[0]="10.36.64.105"
SUBNET_MASK[0]=255.255.255.0
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
DEFAULT_INTERFACE_MODULES=""
ROUTE_GATEWAY[0]=10.36.64.1
ROUTE_COUNT[0]=1
ROUTE_DESTINATION[0]=default
lan900 is created ( bind ) with LAN1 and LAN2
kmsrpra4:/#lanscan -q
0
900 1 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-04-2009 02:31 AM
тАО09-04-2009 02:31 AM
Re: Auto Port Configuration Steps in 11.31
Sagar