HPE Community read-only access December 15, 2018
This is a maintenance upgrade. You will be able to read articles and posts, but not post or reply.
Hours:
Dec 15, 4:00 am to 10:00 am UTC
Dec 14, 10:00 pm CST to Dec 15, 4:00 am CST
Dec 14, 8:00 pm PST to Dec 15, 2:00 am PST
System Administration
cancel
Showing results for 
Search instead for 
Did you mean: 

Auto Port Configuration Steps in 11.31

 
SOLVED
Go to solution
Sagar Sirdesai
Trusted Contributor

Auto Port Configuration Steps in 11.31

HI All
I need to create auto port configuration on a 11.31 Server.

Lan50 and Lan51 are lan cards and I need to create a autoport configuration lan900 as a failover group.

Then assign a IP address
IP_ADDRESS=35.80.66.1
SUBNET_MASK=255.255.240.0

Please provide me the list of commands
7 REPLIES
Michal Kapalka (mikap)
Honored Contributor

Re: Auto Port Configuration Steps in 11.31

Ganesan R
Honored Contributor
Solution

Re: Auto Port Configuration Steps in 11.31

Hi Sagar,

Step by step commands are documented here.

http://book.soundonair.ru/hall2/ch15lev1sec14.html
Best wishes,

Ganesh.
Sagar Sirdesai
Trusted Contributor

Re: Auto Port Configuration Steps in 11.31

Hi Ganeshan

Thanks for the link.
I need to create a lan900 as a failover group for lan50,53

I cannot understand the set of steps to use to assign an IP to lan900 and thn run lanapplyconf.

Sagar
Julián Aimar
Frequent Advisor

Re: Auto Port Configuration Steps in 11.31

This is the doc by HP, link

http://docs.hp.com/en/J4240-90045/index.html

Buena Suerte

Julian
Sagar Sirdesai
Trusted Contributor

Re: Auto Port Configuration Steps in 11.31

I have a doubt here

In the /etc/rc.config.d/netconf

I have an entry for lan50
INTERFACE_NAME[0]="lan50"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""

Now I have created lan900 with lan50 lan51.

So Now I have assign the IP address to lan900

I am using the sam eIp currently assigned to lan50.

What modifications I need to make to the /etc/rc.config.d/netconf file

Remove the entries for lan50 and lan51 and make an entry for lan900 as below


INTERFACE_NAME[0]="lan900"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
Michal Kapalka (mikap)
Honored Contributor

Re: Auto Port Configuration Steps in 11.31

I have a doubt here

In the /etc/rc.config.d/netconf

I have an entry for lan50
INTERFACE_NAME[0]="lan50"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""

Now I have created lan900 with lan50 lan51.

So Now I have assign the IP address to lan900

I am using the sam eIp currently assigned to lan50.

What modifications I need to make to the /etc/rc.config.d/netconf file

Remove the entries for lan50 and lan51 and make an entry for lan900 as below


INTERFACE_NAME[0]="lan900"
IP_ADDRESS[0]="35.80.66.1"
SUBNET_MASK[0]="255.255.240.0"
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""



#==========================================================

an example from my server :

INTERFACE_NAME[0]="lan900"
IP_ADDRESS[0]="10.36.64.105"
SUBNET_MASK[0]=255.255.255.0
BROADCAST_ADDRESS[0]=""
INTERFACE_STATE[0]=""
DHCP_ENABLE[0]=0
INTERFACE_MODULES[0]=""
DEFAULT_INTERFACE_MODULES=""
ROUTE_GATEWAY[0]=10.36.64.1
ROUTE_COUNT[0]=1
ROUTE_DESTINATION[0]=default

lan900 is created ( bind ) with LAN1 and LAN2

kmsrpra4:/#lanscan -q
0
900 1 2
Sagar Sirdesai
Trusted Contributor

Re: Auto Port Configuration Steps in 11.31

Thanks to all

Sagar