- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Auto port aggregation
Operating System - HP-UX
1752790
Members
6689
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2009 05:17 PM
тАО01-06-2009 05:17 PM
Auto port aggregation
Hi
I am configuring four port using APA.
The configuration mode have been set to manual.
Four physical port are in aggregate configuration.
All working fine , but I was makig test , I plug out one net cable and the APA menu in the sam showme 3 port in the aggregate, that is ok.
But when I plug in the net cable back only the aggregated port does not came back
Some recommendation,
Some way to follow.
Regards
W.S
I am configuring four port using APA.
The configuration mode have been set to manual.
Four physical port are in aggregate configuration.
All working fine , but I was makig test , I plug out one net cable and the APA menu in the sam showme 3 port in the aggregate, that is ok.
But when I plug in the net cable back only the aggregated port does not came back
Some recommendation,
Some way to follow.
Regards
W.S
rperez
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2009 05:19 PM
тАО01-06-2009 05:19 PM
Re: Auto port aggregation
I forgot to say that the OS is hpux 11.23
rperez
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-07-2009 03:09 AM
тАО01-07-2009 03:09 AM
Re: Auto port aggregation
Hello,
This is unusual.
a) Can you post contents of
/etc/rc.config.d/hp_apaconf and
/etc/rc.config.d/hp_apaportconf
b) Also, what do these commands show:
# lanscan -v
# lanadmin -x -v 900 (or whatever your PPA is)
Cheers,
VK2COT
This is unusual.
a) Can you post contents of
/etc/rc.config.d/hp_apaconf and
/etc/rc.config.d/hp_apaportconf
b) Also, what do these commands show:
# lanscan -v
# lanadmin -x -v 900 (or whatever your PPA is)
Cheers,
VK2COT
VK2COT - Dusan Baljevic
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP