- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Cant use HP UX Configuration
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 05:32 AM
тАО01-25-2010 05:32 AM
Re: Cant use HP UX Configuration
It may crash the server as well as data.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 05:36 AM
тАО01-25-2010 05:36 AM
Re: Cant use HP UX Configuration
thank you for the tip. we know the mp lan address and will try it that way once with a cross cable directly.
Currently we are accessing the mp lan through a switch.
keeping my fingers crossed for the tip you gave to work.
we are trying to log in the case to HP but we have to do it through a local dealer.so as of now we did'nt get help on this.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 05:48 AM
тАО01-25-2010 05:48 AM
Re: Cant use HP UX Configuration
we are restoring the configuration file that was changed.(netconf located in /etc/rc.config.d/ )
if you could spare your precious time on this also please.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 05:50 AM
тАО01-25-2010 05:50 AM
Re: Cant use HP UX Configuration
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 05:58 AM
тАО01-25-2010 05:58 AM
Re: Cant use HP UX Configuration
we wanted to remove the default route on the server since it was web and when we did netstat -nr
there were 2 defaults - one default with local and one default with global ip.
default 119.2.*.* UG 0 lan4 1500
default 192.168.*.* UG 0 lan0 1500
our network team thinks that the default for local needs to be removed since we were facing request timed out while accessing our server from public.
please suggest if we can remove the route.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 06:07 AM
тАО01-25-2010 06:07 AM
Re: Cant use HP UX Configuration
The fact that both MP LAN and the normal LAN became inaccessible at the same time suggests that the problem might not be in the rx6600, but elsewhere in the network.
Examine your network and find all the components whose failure or mis-configuration could block both the MP LAN and the regular LAN. Verify that all these components are working correctly.
A short press of the power button should initiate a controlled shut-down in any modern HP-UX server, including the rx6600.
Disconnecting the power will certainly reset the MP too, allowing you to regain access to the MP if the problem is in the rx6600. But there is a gentler way to do it: the rx6600 MP has an externally-accessible reset button, between the VGA connector and the MP activity LEDs.
Please look at Figure 1 in this document to find the MP reset button:
http://bizsupport2.austin.hp.com/bc/docs/support/SupportManual/c01884294/c01884294.pdf
If the server is not accessible through the regular LAN and the MP LAN is also not accessible, you cannot even troubleshoot the server any further without the console cable.
MK
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 06:18 AM
тАО01-25-2010 06:18 AM
Re: Cant use HP UX Configuration
route delete default
Also configure your MP & keep it ready. It may help you to troubleshoot the problems.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 06:43 AM
тАО01-25-2010 06:43 AM
Re: Cant use HP UX Configuration
we checked the firewall, ip and everything is fine.
any possible suggestions to check collision or conflicts ?
we unplugged the server and left it for sometime but found no conflicts either.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 06:48 AM
тАО01-25-2010 06:48 AM
Re: Cant use HP UX Configuration
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-25-2010 06:58 AM
тАО01-25-2010 06:58 AM
Re: Cant use HP UX Configuration
i dont understand. maybe i need to change the port for the mp lan for this server on the switch n check