- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: EMC power path in rhel5
Operating System - Linux
1753856
Members
7285
Online
108809
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2011 05:48 AM
тАО01-18-2011 05:48 AM
EMC power path in rhel5
Team,
How to perform emc power path?here after creating mount points based on the emcpower.after restarting the server is not booting?it's not reading emc power file while booting time?
following steps:
тАв emcpreg -install
тАв use key given for registration
тАв powermt check_registration
тАв powermt set policy=co dev=all
тАв powermt display dev=all
тАв /etc/init.d/PowerPath start
It's correct?please guide me.
Regards,
Seenivasan P
How to perform emc power path?here after creating mount points based on the emcpower.after restarting the server is not booting?it's not reading emc power file while booting time?
following steps:
тАв emcpreg -install
тАв use key given for registration
тАв powermt check_registration
тАв powermt set policy=co dev=all
тАв powermt display dev=all
тАв /etc/init.d/PowerPath start
It's correct?please guide me.
Regards,
Seenivasan P
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2011 05:57 AM
тАО01-18-2011 05:57 AM
Re: EMC power path in rhel5
hi,
check for example this link :
http://www.thegeekstuff.com/2009/09/how-to-install-and-configure-emc-powerpath-on-linux/
http://sundar5.wordpress.com/2010/01/22/multipath/
your procedure seems to be ok,
i followed the offcial admin guide for the installation ( from EMC ) installed on HP-UX / RHEL / Centos, without any problem.
mikap
check for example this link :
http://www.thegeekstuff.com/2009/09/how-to-install-and-configure-emc-powerpath-on-linux/
http://sundar5.wordpress.com/2010/01/22/multipath/
your procedure seems to be ok,
i followed the offcial admin guide for the installation ( from EMC ) installed on HP-UX / RHEL / Centos, without any problem.
mikap
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2011 06:51 AM
тАО01-18-2011 06:51 AM
Re: EMC power path in rhel5
ok.but after creatng mount points i m going to restart the server in that time server is not booting..
before restarting the server i made changes in /etc/lvm/lvm.conf file
commented the following line:
# filter = [ "a/.*/" ]
and added the below line:
filter = [ "a/c0d0.*/", "a/emcpower.*/", "r/.*/" ]
so what was the issue?i hope emcpower path file is not read by while server booting time.
please help me to reslove the issue.
Regards,
Seenivasan P
before restarting the server i made changes in /etc/lvm/lvm.conf file
commented the following line:
# filter = [ "a/.*/" ]
and added the below line:
filter = [ "a/c0d0.*/", "a/emcpower.*/", "r/.*/" ]
so what was the issue?i hope emcpower path file is not read by while server booting time.
please help me to reslove the issue.
Regards,
Seenivasan P
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-18-2011 06:55 AM
тАО01-18-2011 06:55 AM
Re: EMC power path in rhel5
Did you not fix this already in an earlier Post good sir?
You were alerdy told to leave your default Filter on and work your way to customising a proper LVM filter to works for you.
You were alerdy told to leave your default Filter on and work your way to customising a proper LVM filter to works for you.
Hakuna Matata.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP