- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: HP-UX and Samba install issue
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2011 03:05 PM
тАО01-03-2011 03:05 PM
We are trying to get CIFS working on HP-UX so developers can start using Eclipse IDE (on WinXP laptops) to connect to the Unix box.
We have installed CIFS server, details are as follows
HP-UX B.11.31 U ia64
CIFS-CLIENT A.02.02.02 HP CIFS Client
CIFS-SERVER A.02.04 HP CIFS Server
When trying to map a drive to the UNIX box from Windows Explorer, we are getting a authentication box but neither the LAN or UNIX userid/password are getting past the authentication box.
I tried mapping \\unixhostname\userid , \\unixhostname\tmpsort , \\unixhostname\homes but can't get past the authentication box.
smbd is running on the UNIX box under root
ps -aef|grep smbd
/opt/samba/bin/smbd -D -s /etc/opt/samba/smb.conf
Attached is the SAMBA config file (after removing the comments).
The following command gives this error
smbclient ├в L hostname123
Password:
session setup failed: NT_STATUS_LOGON_FAILURE
The logfile posts the following errors
read_data: read failure for 4 bytes to client xxx.xxx.xxx.xxx. Error = Connection reset by peer
The nmbd logfile shows the following
[2011/01/03 16:45:29, 0] nmbd/nmbd_namequery.c:query_name_response(109)
query_name_response: Multiple (2) responses received for a query on subnet xxx.xxx.xxx.xxx for name someworkgroup<1d>.
This response was from IP xxx.xxx.xxx.xxx, reporting an IP address of xxx.xxx.xxx.xxx.
winbindd is not running on the UNIX box.
Ideally, we would want the users to be authenticated using the unix id/password while establishing the connection to the UNIX shares.
IPs and domain names have been scrubbed above.
Please advise...
Thanks
Sridhar
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2011 08:41 PM
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2011 08:52 PM
тАО01-03-2011 08:52 PM
Re: HP-UX and Samba install issue
There are no details such as netbios name, security, password server etc defined.
Also, please enable the section
username map = /etc/opt/samba/smbusers.map
if you want to map windows user to UNIX.
Shibin
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-03-2011 09:34 PM
тАО01-03-2011 09:34 PM
Re: HP-UX and Samba install issue
plz find the attached configuration file.
hope it will help u.
Regards/Morshed.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-05-2011 01:04 PM
тАО01-05-2011 01:04 PM
Re: HP-UX and Samba install issue
The following changes have been made but still not able to connect from windows explorer
netbios name = unixboxname
password server = *
username map = /etc/opt/samba/smbusers.map
Created smbusers.map file with the following info, added both the lines as wasn't sure if it'll use LAN_ID or WIN_MACHINE_NAME.
unixname = LAN_ID
unixname = win_machine_name
With respect to security parameter, this is a stand alone UNIX box with WinXP users connecting. So, should I be using security=user ?
Thank You
Sridhar
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-06-2011 09:00 PM
тАО01-06-2011 09:00 PM