- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: HPUX not recognizing the luns
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 08:36 AM
тАО12-18-2008 08:36 AM
And fI have connected the FC Cable from the Cisco Switch Port to the HP 4GB fiber channel Pass-through Module.
Now I have run ioscan on all the blades in the Enclosure and the blade is not recognizing the luns....
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 08:57 AM
тАО12-18-2008 08:57 AM
SolutionMake sure the World Wide Name of the Lun is matching the fiber card.
Make sure the hba cards are compatible with 4 GB fiber media.
If this is a new setup you may need to reboot or try insf -C disk
Then ioscan again
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 09:04 AM
тАО12-18-2008 09:04 AM
Re: HPUX not recognizing the luns
How can I check if World Wide Name of the Lun is matching the fiber card.
Yes u r right.... this is a new setup
reboot individual blade or the entire enclosure
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 09:44 AM
тАО12-18-2008 09:44 AM
Re: HPUX not recognizing the luns
For EMC Clarion you need to register a key in server to deduct the new lun and also you need to set the policy as clarion please check the below command.
Check the man page and take the help of EMC helpdesk to register the key.
#powermt set policy=co dev=all
then run
#powermt config
and
#powermt save
then take a reboot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-18-2008 09:57 AM
тАО12-18-2008 09:57 AM
Re: HPUX not recognizing the luns
# man powermt
No manual entry for powermt.
# powermt set policy=co dev=all
sh: powermt: not found.
#
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-19-2008 02:15 AM
тАО12-19-2008 02:15 AM
Re: HPUX not recognizing the luns
Plz perform below activity in the enviorenmemt.
1). Have you mapped lun with host from storage side. Chk it
2). Have you created zone in SAN switch. Chk it.
3). Clarion agent should be installed in host side.
4). Power Path Should be installed & configured in host.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-19-2008 08:58 AM
тАО12-19-2008 08:58 AM
Re: HPUX not recognizing the luns
Man page:
powermt
Usage:
powermt
powermt check [force] [hba=
powermt check_registration
powermt config
powermt display [ports] [dev=
powermt display options
powermt display paths [every=<#seconds>]
powermt display unmanaged
powermt manage {dev=
powermt unmanage {dev=
powermt load [file=
powermt remove [force] [hba=
powermt restore [hba=
[force [hba=
powermt save [file=
powermt set mode=active|standby [hba=
powermt set periodic_autorestore=on|off
powermt set policy={ad|bf|co|lb|li|nr|re|rr|so} [dev=
powermt set priority=
powermt set write_throttle={on|off} [dev=
powermt set write_throttle_queue=
powermt update lun_names
powermt version