How to change the kernel parameter

[praveen..]

Hi,
I need to install the oracle 10g in hp-ux b.11.11

when i am trying to install oracle 10g, i got this error:

=======================================================================



Checking recommended operating system patches

Checking for PHNE_31097; found PHNE_31097. Passed

Checking for PHSS_31221; found PHSS_31221. Passed

Checking for PHSS_32508; found Not found. Failed <<<<

Checking for PHSS_32509; found Not found. Failed <<<<

Checking for PHSS_32510; found Not found. Failed <<<<

Checking for PHSS_30970; found PHSS_30970. Passed

Checking for PHSS_32731; found PHSS_32731. Passed

Checking for PHCO_31312; found PHCO_31312. Passed

Checking for PHCO_30275; found PHCO_30275. Passed

Checking for PHNE_28923; found PHNE_28923. Passed

Check complete. The overall result of this check is: Failed <<<<

Problem: Some recommended patches are missing (see above).

Recommendation: You may actually have installed patches which have obsoleted these, in which case you can successfully continue with the install. If you have not, it is recommended that you do not continue. Refer to the readme to find out how to get the missing patches.

=======================================================================



Checking kernel parameters

Checking for ksi_alloc_max=32768; found ksi_alloc_max=25760. Failed <<<<

Checking for max_thread_proc=256; found max_thread_proc=64. Failed <<<<

Checking for maxdsiz=1073741824; found maxdsiz=268435456. Failed <<<<

Checking for maxdsiz_64bit=2147483648; found maxdsiz_64bit=1073741824. Failed <<<<

Checking for maxssiz=134217728; found maxssiz=134217728. Passed

Checking for maxssiz_64bit=1073741824; found maxssiz_64bit=134217728. Failed <<<<

Checking for maxswapchunks=16384; found maxswapchunks=16384. Passed

Checking for maxuprc=3687; found maxuprc=512. Failed <<<<

Checking for msgmap=4098; found msgmap=32202. Passed

Checking for msgmni=4096; found msgmni=3220. Failed <<<<

Checking for msgseg=32767; found msgseg=32767. Passed

Checking for msgtql=4096; found msgtql=32200. Passed

Checking for ncsize=34816; found ncsize=32928. Failed <<<<

Checking for nfile=63488; found nfile=50348. Failed <<<<

Checking for nflocks=4096; found nflocks=3220. Failed <<<<

Checking for ninode=34816; found ninode=27808. Failed <<<<

Checking for nkthread=7184; found nkthread=5651. Failed <<<<

Checking for nproc=4096; found nproc=3220. Failed <<<<

Checking for semmap=4098; found semmap=16102. Passed

Checking for semmni=4096; found semmni=16100. Passed

Checking for semmns=8192; found semmns=32200. Passed

Checking for semmnu=4092; found semmnu=64. Failed <<<<

Checking for semvmx=32767; found semvmx=32767. Passed

Checking for shmmax=1073741824; found shmmax=4294967296. Passed

Checking for shmmni=512; found shmmni=1024. Passed

Checking for shmseg=120; found shmseg=120. Passed

Checking for vps_ceiling=64; found vps_ceiling=16. Failed <<<<

Check complete. The overall result of this check is: Failed <<<<

Problem: The kernel parameters do not meet the minimum requirements (see above).

Recommendation: Perform operating system specific instructions to update the kernel parameters.

=======================================================================







Please let me know how can i change the kernel parameters:

I am doing:
sam> kernal configuration> configurable parameters >
then i used "space" to select any parameter and the "action" , then "modify configurable parameter"

then it shows me the " formula value" & "current value".


I am also facing some problem with the installation of these patches, I had already opened a new thread for it.


Please suggest how can change these kernel parameters value.

Thanks

[Jaime Bolanos Rojas.]

Praven, if you are running 11.11 then you should go to Sam, Kernel configuration, then Kcweb (kernel configuration ) character mode, then tunables, then select the tunable and you will have some option at the bottom to modify the values, usually m to modify the value...

Regards,

Jaime.

[Jaime Bolanos Rojas.]

Praven,

My apologies, that was my 11.23, you need an 11.11.

I will give it to you in just one second, sorry!

Jaime.

[Karsten Löperick]

Hello praveen,

changing Kernelparams are not too difficult.
I general you only have to type in the new value in decimal ( e.g. 100000 ) or hexadecimal ( 0x186a0 ) or a new formula ( e.g ( "(nkthread + 90212)" ). It is also possible to overwrite formulas with decimal or hexadecimal values. If the "value" a formula then you will see the calculated calue otherwise the formula/value are the same as the current value.
But be careful with the dependencies to other kernel params.

So I hope that helps a bit.

Karsten

[Jaime Bolanos Rojas. · Accepted solution]

Praven,

From the command line, I did not like the options in SAM,

- go to /stand/build

- run: system_prep -s system

- make changes to kernel with kmsystem and kmtune ( take a look at man pages if necessary )

- mk_kernel -s ./system

- backup old kernel

cp /stand/system /stand/system.old
cp /stand/vmunix /stand/vmunix.old
cp -R dlkm dlkm.vmunix.old

- kmupdate ( this will schedule the installation of new kernel )

- Reboot

- check to see that paremeters were changed.

Regards,

Jaime.

[praveen..]

Hi,
i am afraid to change the kernal parameters using command, please suggest me using SAM

Thanks

[Karsten Löperick]

Hello again,

I forgot to tell you that you can use SAM . Thats the way how I am doing kernel changings. So don´t be afraid - it is easy specially with SAM.

Greetings

Karsten

[praveen..]

every parameter is in formula value,
i dont want to use the formula, i want to change the values in decimal.

please suggest

[Pete Randall]

SAM > Kernel Configuration > Configurable Paramaters > then select the parameter you wish to change, click on Actions > Modify Configurable Parameter and plug in the required value in the Formula/Value window. This window can contain either an absolute value or a formula. If it contains a formula (like maxusers X something plus something else), you can just plug in an absolute value instead. In fact it is commonly suggested to use ablolute values rather than formulas (formulae?). When you have changed all the required parameters, the click on Actions > Process New Kernel. SAM will build your new kernel and then ask you to click OK to move the kernel into place and reboot.


Pete

[Pete Randall]

I should also add that there is a button under Actions called "Show Values in Hex/Decimal". You can use this to switch back and for from hex to decimal.


Pete