Operating System - HP-UX
1748181 Members
3637 Online
108759 Solutions
New Discussion юеВ

Re: How to restore OS from an Ignite-UX Recovery Archive Server

 
SOLVED
Go to solution
Md. Minhaz Khan
Super Advisor

How to restore OS from an Ignite-UX Recovery Archive Server

Dear Concern
I have configured an Ignite-UX Recovery Archive Server and successfully took backup using "make_net_recovery -s 192.168.1.10 -x inc_entire=vg00".

Now my query is if my boot disk becomes corrupted then how can reinstall from the created image?

My OS is B.11.11 and system model is rp3440

I have found the following steps to recover a non-bootable system:
1)Power up the system
2)Interrupt the boot
3) Boot from the ignite-UX sertver--->What is the command
...........
.........
.......


Thanks
Minhaz
8 REPLIES 8
Michal Kapalka (mikap)
Honored Contributor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

bo lan.192.168.1.10
sujit kumar singh
Honored Contributor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

Hi

then boot the system over LAN(this shall require the ignite server to be configured to allow remote boot) then ignite install the system.
this shall need setting up /etc/bootptab on ignite server to be edited toput the MAC Address and temporary IP of the server to be installed.
and allowing the tftp, bootps and instl_boots services in /etc/inetd.conf of the ignite server.

OR u can boot the system using boot DVD having the same version of ignite as the Ignite server, then choose "boot from DVD and network based installtion" -- you shall be prompted for the system IP address, gateway,. subnet mask and the client shall be able to pickup the config and the archive from the server.

regards
sujit

Md. Minhaz Khan
Super Advisor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

Dear concern

When i interrupt the boot i have found following menu:


Command Description
------- -----------
BOot [PRI|ALT|] Boot from specified path
PAth [PRI|ALT] [] Display or modify a path
SEArch [DIsplay|IPL] [] Search for boot devices

COnfiguration menu Displays or sets boot values
INformation menu Displays hardware information
SERvice menu Displays service commands

DIsplay Redisplay the current menu
HElp [|] Display help for menu or command
RESET Restart the system


I did not found "boot lan" option

I have also give search :

Main Menu: Enter command or menu > sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate).


IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ----
P0 0/0/2/0.0 ide.0 Random access media 1 ---------->This is for CD-ROM

P1 0/1/1/0.1 intscsia.1 Random access media 1

P2 0/1/1/0.0 intscsia.0 Random access media 1

P3 0/1/1/1.1 intscsib.1 Sequential access media 1 -------->This is for Tape Drive.

P4 0/2/1/0/4/0.8 Random access media 13


but did not find lan options

Thanks

Minhaz
sujit kumar singh
Honored Contributor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

once in the BCH Main menu ,

try giving that command boot lan.

and see , i am not too sure about this PARSIC system.
Or alterbatively you can boot using the core OS and install DVD and choose the option network based installationa and choose/provide Ignite server IP address,gateway and IP addresses.
regards
sujit
Michal Kapalka (mikap)
Honored Contributor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

hi,

check this link :

http://www.docs.hp.com/en/5992-5309/5992-5309.pdf

chapter 9 i about booting,

boot lan.IP install

mikap
johnsonpk
Honored Contributor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

Hi Minhaz,


Detailed booting instruction with screen shot is avaialable on the below link


http://docs.hp.com/en/5992-5309/ch09s05.html?btnPrev=%AB%A0prev


http://docs.hp.com/en/5992-5309/ch09s06.htmls


Rgds

Johnson
Basheer_2
Trusted Contributor
Solution

Re: How to restore OS from an Ignite-UX Recovery Archive Server

Minhaz,

in our Integrity 11.23 this is how we do

my /etc/bootptab is like this on the ignite server ( you an copy an entry from the existing one)

cat /etc/bootpab
server\
bf=/opt/ignite/boot/nbp.efi:\
hn:\
vm=rfc1048:\
ht=ether:\
ha=0018FE280160:\
ip=204.187.168.143:\
sm=255.255.255.0
gw=204.187.168.254

You need to change 3 items in this file

server is your ignite client
ha is a H/w address. get it from ipconfig lan0 or do a lanscan
IP is the ip addr of your client
SM and gw are the subnet mask and the gateway address

# Resoting Client from ignite
1-Reboot the server and go to efi shell and create db profile
Shell>dbprofile -dn testprofile -sip 204.187.168.207.x -cip 204.187.168.143 -gip 204.187.168.254 -m 255.255.255.0 -b "/opt/ignite/boot/nbp.efi"
2-Exit efi shell.
3- Go to boot configuration 4- add a boot option 5-select lan A
5-Give name of boot option "Lan A" 6-select db-profile 7-Confirm Y
7-Exit from main menu 8-Select LanA and boot from Lan....


hope this will helps.
Md. Minhaz Khan
Super Advisor

Re: How to restore OS from an Ignite-UX Recovery Archive Server

Thanks a lot to every body for helping me.

Thanks
Minhaz