- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Hpssacli RAID10 to Raid1
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-24-2019 02:48 AM
04-24-2019 02:48 AM
Hpssacli RAID10 to Raid1
Hi,
I made a mistake, I have added 2 new disk to rhe worng ld, It had transformed the ld1 in Raid 10. Now I try to remove the disks from Array A to assigned them to Array B, but it doesnt work.
Let me know if it's possible without breaking the OS ?
hpssacli ctrl slot=0 array A remove drives=2I:1:5,2I:1:6
Error: This command did not complete properly. Please check your configuration
for possible hardware or configuration problems. Use the "show" command
on devices to show additional details about the configuration.
hpssacli ctrl slot=0 show config
Smart Array P440ar in Slot 0 (Embedded) (sn: PDNLH0BRH914NC)
Port Name: 1I
Port Name: 2I
Internal Drive Cage at Port 1I, Box 1, OK
Internal Drive Cage at Port 2I, Box 1, OK
array A (SAS, Unused Space: 572140 MB)
logicaldrive 1 (279.4 GB, RAID 1+0, OK)
physicaldrive 1I:1:1 (port 1I:box 1:bay 1, SAS, 300 GB, OK)
physicaldrive 1I:1:2 (port 1I:box 1:bay 2, SAS, 300 GB, OK)
physicaldrive 2I:1:5 (port 2I:box 1:bay 5, SAS, 1200.2 GB, OK)
physicaldrive 2I:1:6 (port 2I:box 1:bay 6, SAS, 1200.2 GB, OK)
array B (SAS, Unused Space: 0 MB)
logicaldrive 2 (1.1 TB, RAID 1, OK)
physicaldrive 1I:1:3 (port 1I:box 1:bay 3, SAS, 1200.2 GB, OK)
physicaldrive 1I:1:4 (port 1I:box 1:bay 4, SAS, 1200.2 GB, OK)
hpssacli ctrl slot=0 ld 1 modify raid=1
Error: "raid=1" is not a valid option for logicaldrive 1
Available options are:
0
1+0 (current value)
5
6 (default value)
Best.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
05-10-2019 11:15 AM
05-10-2019 11:15 AM
Re: Hpssacli RAID10 to Raid1
Hello ,
It is theoritically possible to split RAID 1+0 to RAID 1.
However, it cannot be done in Online Mode. You would have to reboot the server and boot to the HPSSA in offline mode and then you will see an option to split the Mirroring.
However, it is recommended to take a Backup of the Data before you proceed with the Update
Regards,,
Venkata Ramana Srimushnam