- Community Home
- >
- Servers and Operating Systems
- >
- Legacy
- >
- Operating System - Tru64 Unix
- >
- Re: Install TZ89 in a 4100 with Tru64 4.0G
Operating System - Tru64 Unix
1752808
Members
5625
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Go to solution
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2006 10:24 PM
тАО01-30-2006 10:24 PM
Hi
I have two 4100 with 4.0G and TZ89.
in console mode with "show dev" i see:
mkc100 TZ89.
when boot with the command scu scan edt, i can't see a TZ.
Why? need a driver? How I can install it ?
Thanks to all
I have two 4100 with 4.0G and TZ89.
in console mode with "show dev" i see:
mkc100 TZ89.
when boot with the command scu scan edt, i can't see a TZ.
Why? need a driver? How I can install it ?
Thanks to all
Solved! Go to Solution.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2006 10:38 PM
тАО01-30-2006 10:38 PM
Solution
Hello
Does scu see anything on bus 2 address 1?
Did you connect TZ89 to newly installed controller or to existing one (hope you have no address conflict)?
Anyway, you can try to boot generic kernel:
>>> boot -file genvmunix
and see if something changed.
If you installed a new controller with tape device, you must boot with genvmunix and rebuild the kernel with doconfig.
Regards
Does scu see anything on bus 2 address 1?
Did you connect TZ89 to newly installed controller or to existing one (hope you have no address conflict)?
Anyway, you can try to boot generic kernel:
>>> boot -file genvmunix
and see if something changed.
If you installed a new controller with tape device, you must boot with genvmunix and rebuild the kernel with doconfig.
Regards
In vino veritas, in VMS cluster
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2006 11:17 PM
тАО01-30-2006 11:17 PM
Re: Install TZ89 in a 4100 with Tru64 4.0G
It's OK
Thanks
Thanks
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-30-2006 11:19 PM
тАО01-30-2006 11:19 PM
Re: Install TZ89 in a 4100 with Tru64 4.0G
I have found a solution to this question
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP