- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- P2000 G3 and HP-UX 11.31
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-30-2011 08:51 AM
10-30-2011 08:51 AM
P2000 G3 and HP-UX 11.31
Hi
I have an actual t solution with MSA1000 and HPUX 11.31.
I want to replace the MSA1000 with a P2000 G3 FC.
I have configure the Vdisk and volumens and have been presented to the HPUX hbas, the profile have been changed to HPUX too.
When I do an ioscan , I can see the P2000 but appear an NO_HW.
I will try to put the latest FC driver but if some other suggestion are available please let me know.
Other question if the actual MSA1000 have been seen by the HPUX, will be required the latest fc driver to recognize the new P2000 G3 FC?
Thank
W.S
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-30-2011 12:11 PM
10-30-2011 12:11 PM
Re: P2000 G3 and HP-UX 11.31
Am I correct that you installed P2000 in place of MSA1000 exactly in the same ports on the switch? You made ioscan without parameters and insf -e, and then you see NO_HW in output of ioscan -fn — right?
It would be good to see output of ioscan -fn and ioscan -fnN from this system. Can you attach this?
Ivan.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-30-2011 04:44 PM
10-30-2011 04:44 PM
Re: P2000 G3 and HP-UX 11.31
For compatibility you can check out all the details at HP's SPOCK site.
Oftentimes when you connect a new storage (target) to a HP-UX 11.31 server you need to run the "scsimgr replace_wwid" command. Look into syslog after you have run a ioscan to see if any such messages appear and then run the commands as described.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-30-2011 05:13 PM
10-30-2011 05:13 PM
Re: P2000 G3 and HP-UX 11.31
I have connected the P2000 FC ports to new SAN switch port.
The P2000 have been configured to the same zone of the HPUX.
The machine have been rebooted some time.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-31-2011 11:51 AM
10-31-2011 11:51 AM