System Administration
cancel
Showing results for 
Search instead for 
Did you mean: 

Please help me to fix the logic driver!

Wangjerfee
Occasional Advisor

Please help me to fix the logic driver!

On a Rx2800 server , the hard disk of a RAID group was failed, I change the disk to a new one, and after the synchronzition , the stat of the RAID became OK, but in syslog.log , there many fault report like below:

May 30 16:39:52 qd1350oms vmunix: CISS: RAID SA controller on hardware path 0/0/0/1/0/0/0 has detected a fatal IO
May 30 16:39:52 qd1350oms vmunix: error on logical drive 0:
May 30 16:39:52 qd1350oms vmunix: Logical Block Address: 0x7d38ff8
May 30 16:39:52 qd1350oms vmunix: Logical Block Count: 8
May 30 16:39:52 qd1350oms vmunix: Logical Command: 0x20
May 30 16:39:52 qd1350oms vmunix: Fatal Drive Connector: 1I
May 30 16:39:52 qd1350oms vmunix: Fatal Drive Enclosure: 1
May 30 16:39:52 qd1350oms vmunix: Fatal Drive Bay: 2
May 30 16:39:52 qd1350oms vmunix: WWID: 0x5000cca00086f5ed

It seemed something wrong with the harddisk which I replaced(Enclosure: 1 Bay: 2),  but the stat of  this disk in sautil and saconfig was normal.

Can anyone tell me how to correct the bad block and stop the error message?

Thanks!

Below is the message of sautil and saconfig:

 

qd1350oms,sys,root # sautil /dev/ciss0

******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.20 ****
**** ****
**** (C) Copyright 2003-2010 Hewlett-Packard Development Company, L.P. ****
******************************************************************************

 

---- DRIVER INFORMATION ------------------------------------------------------

Driver State........................ READY

---- CONTROLLER INFORMATION --------------------------------------------------

Controller Product Number........... P410i
Controller Product Name............. HP PCIe SmartArray P410i
Controller mode..................... RAID MODE
Hardware Path....................... 0/0/0/1/0/0/0
Serial Number....................... ----
Device File......................... /dev/ciss0
Hardware Revision................... 'C'
Boot Block Revision................. 2.31
Firmware Revision (running)......... 5.78
Firmware Revision (in ROM).......... 5.78
Firmware Revision (inactive)........ 3.66
# of Logical Drives................. 3
# of Physical Disks Configured...... 6
# of Physical Disks Detected........ 6
Logical Drive Rebuild Priority...... 0 (low)
Array Capacity Expansion Priority... 0 (low)
Auto-Fail Missing Disks at Boot..... disabled
SCSI Transfer Detection Mode........ Auto Detect
Controller Path Selection Method.... default
Max # of Logical Drives............. 64
Last firmware lockup................ 0


---- ARRAY ACCELERATOR (CACHE) INFORMATION -----------------------------------

Array Accelerator Board Present?.... yes
Cache Configuration Status.......... cache enabled
Cache Ratio......................... 25% Read / 75% Write
Total Cache Size (MB)............... 400
Read Cache........................ 100
Write Cache....................... 300
Transfer Buffer................... 000
Battery Pack Count.................. 1
Battery Status (pack #1)............ ok


---- LOGICAL DRIVE SUMMARY ---------------------------------------------------

# RAID Size Status

0 1+0 139979 MB OK
1 1+0 139979 MB OK
2 1+0 139979 MB OK


---- SAS/SATA DEVICE SUMMARY -------------------------------------------------

Location Ct Enc Bay WWID Type Capacity Status

internal 1I 1 1 0x500003946831a9b2 DISK 146.8 GB OK
internal 1I 1 2 0x5000cca00086f5ed DISK 146.8 GB OK
internal 1I 1 3 0x500003946831b3e6 DISK 146.8 GB OK
internal 1I 1 4 0x500003946831aabe DISK 146.8 GB OK
internal 2I 1 5 0x500003946831a9fa DISK 146.8 GB OK
internal 2I 1 6 0x500003946831a9f6 DISK 146.8 GB OK


---- SAS/SATA ENCLOSURE SUMMARY ----------------------------------------------

Location Ct Enc Expander_count Bay_count SEP_count

internal 1I 1 0 4 1
internal 2I 1 0 4 1


---- LOGICAL DRIVE 0 ---------------------------------------------------------

Logical Drive Device File........... /dev/dsk/c0t0d0
Fault Tolerance Mode................ RAID 1+0 (Disk Mirroring)
Logical Drive Size.................. 139979 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 2

Participating Physical Disk(s)...... Ct:Enc:Bay:WWID
1I:1:1:0x500003946831a9b2
1I:1:2:0x5000cca00086f5ed

Participating Spare Disk(s)......... Ct:Enc:Bay:WWID
none

Stripe Size......................... 128 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA0D0317D
Media Exchange Detected?............ no


---- LOGICAL DRIVE 1 ---------------------------------------------------------

Logical Drive Device File........... /dev/dsk/c0t0d1
Fault Tolerance Mode................ RAID 1+0 (Disk Mirroring)
Logical Drive Size.................. 139979 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 2

Participating Physical Disk(s)...... Ct:Enc:Bay:WWID
1I:1:3:0x500003946831b3e6
1I:1:4:0x500003946831aabe

Participating Spare Disk(s)......... Ct:Enc:Bay:WWID
none

Stripe Size......................... 128 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA014ED7B
Media Exchange Detected?............ no


---- LOGICAL DRIVE 2 ---------------------------------------------------------

Logical Drive Device File........... /dev/dsk/c0t0d2
Fault Tolerance Mode................ RAID 1+0 (Disk Mirroring)
Logical Drive Size.................. 139979 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 2

Participating Physical Disk(s)...... Ct:Enc:Bay:WWID
2I:1:5:0x500003946831a9fa
2I:1:6:0x500003946831a9f6

Participating Spare Disk(s)......... Ct:Enc:Bay:WWID
none

Stripe Size......................... 128 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA0160505
Media Exchange Detected?............ no

---- SAS/SATA DEVICE 1I:1:1:0x500003946831a9b2 [DISK] ------------------------

Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 1
WWID............................................. 0x500003946831a9b2
Disk WWID........................................ 0x500003946831a9b0
Device Type...................................... DISK
Disk Capacity.................................... 146.8 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EH0146FCBVB
Device Serial Number............................. Confidential Info Erased
Device Firmware Version.......................... HPD3
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

 

---- SAS/SATA DEVICE 1I:1:2:0x5000cca00086f5ed [DISK] ------------------------

Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 2
WWID............................................. 0x5000cca00086f5ed
Disk WWID........................................ 0x5000cca00086f5ec
Device Type...................................... DISK
Disk Capacity.................................... 146.8 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ DG146BAAJB
Device Serial Number............................. ----
Device Firmware Version.......................... HPDA
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. MARK BAD FAILED
Media Type....................................... HDD

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

 

---- SAS/SATA DEVICE 1I:1:3:0x500003946831b3e6 [DISK] ------------------------

Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 3
WWID............................................. 0x500003946831b3e6
Disk WWID........................................ 0x500003946831b3e4
Device Type...................................... DISK
Disk Capacity.................................... 146.8 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EH0146FCBVB
Device Serial Number............................. -----
Device Firmware Version.......................... HPD3
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

 

---- SAS/SATA DEVICE 1I:1:4:0x500003946831aabe [DISK] ------------------------

Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 4
WWID............................................. 0x500003946831aabe
Disk WWID........................................ 0x500003946831aabc
Device Type...................................... DISK
Disk Capacity.................................... 146.8 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EH0146FCBVB
Device Serial Number............................. ----
Device Firmware Version.......................... HPD3
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

 

---- SAS/SATA DEVICE 2I:1:5:0x500003946831a9fa [DISK] ------------------------

Connector Location............................... internal
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 5
WWID............................................. 0x500003946831a9fa
Disk WWID........................................ 0x500003946831a9f8
Device Type...................................... DISK
Disk Capacity.................................... 146.8 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EH0146FCBVB
Device Serial Number............................. ----
Device Firmware Version.......................... HPD3
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG
Media Type....................................... HDD

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

 

---- SAS/SATA DEVICE 2I:1:6:0x500003946831a9f6 [DISK] ------------------------

Connector Location............................... internal
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 6
WWID............................................. 0x500003946831a9f6
Disk WWID........................................ 0x500003946831a9f4
Device Type...................................... DISK
Disk Capacity.................................... 146.8 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EH0146FCBVB
Device Serial Number............................. ----
Device Firmware Version.......................... HPD3
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG
Media Type....................................... HDD

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

 

---- SAS/SATA DEVICE :0:0:0x5001438018ac9b2f [SES] ---------------------------

Connector Location............................... internal
Connector........................................
Enclosure........................................ 0
Bay.............................................. 0
WWID............................................. 0x5001438018ac9b2f
Device Type...................................... SES
Device Vendor ID................................. PMCSIERA
Device Product ID................................ SRC 8x6G
Device Serial Number.............................----
Device Firmware Version.......................... RevC
M&P Data Stamped?................................ no
Last Failure Reason.............................. none

 

******************************************************************************
**** End of SAUTIL Output ****
******************************************************************************

 

 

 

qd1350oms,sys,root # saconfig /dev/ciss0

******************** SmartArray RAID Controller /dev/ciss0 ********************

Auto-Fail Missing Disks at Boot = disabled
Cache Configuration Status = cache enabled
Cache Ratio = 25% Read / 75% Write

---------- PHYSICAL DRIVES ----------

Location Ct Enc Bay WWID Size Status

Internal 1I 1 1 0x500003946831a9b2 146.8 GB OK
Internal 1I 1 2 0x5000cca00086f5ed 146.8 GB OK
Internal 1I 1 3 0x500003946831b3e6 146.8 GB OK
Internal 1I 1 4 0x500003946831aabe 146.8 GB OK
Internal 2I 1 5 0x500003946831a9fa 146.8 GB OK
Internal 2I 1 6 0x500003946831a9f6 146.8 GB OK

---------- LOGICAL DRIVE 0 ----------

Device File = /dev/dsk/c0t0d0
RAID Level = 1+0
Size = 139979 MB
Stripe Size = 128 KB
Status = OK

Participating Physical Drive(s):

Ct Enc Bay WWID
1I 1 1 0x500003946831a9b2
1I 1 2 0x5000cca00086f5ed

Participating Spare Drive(s):

None

---------- LOGICAL DRIVE 1 ----------

Device File = /dev/dsk/c0t0d1
RAID Level = 1+0
Size = 139979 MB
Stripe Size = 128 KB
Status = OK

Participating Physical Drive(s):

Ct Enc Bay WWID
1I 1 3 0x500003946831b3e6
1I 1 4 0x500003946831aabe

Participating Spare Drive(s):

None

---------- LOGICAL DRIVE 2 ----------

Device File = /dev/dsk/c0t0d2
RAID Level = 1+0
Size = 139979 MB
Stripe Size = 128 KB
Status = OK

Participating Physical Drive(s):

Ct Enc Bay WWID
2I 1 5 0x500003946831a9fa
2I 1 6 0x500003946831a9f6

Participating Spare Drive(s):

None