System Administration
cancel
Showing results for 
Search instead for 
Did you mean: 

Please help to start HP server

rvn152
Occasional Visitor

Please help to start HP server

Hello

Can you please help to start Hp server. Or to understand the root of the problem.

The log is the next:

 

Firmware Version  46.34

Duplex Console IO Dependent Code (IODC) revision 1
------------------------------------------------------------------------------
   (c) Copyright 1995-2004, Hewlett-Packard Company, All rights reserved
------------------------------------------------------------------------------

  Processor   Speed            State           CoProcessor State  Cache Size
  Number                                       State              Inst    Data
  ---------  --------   ---------------------  -----------------  ------------
      0     1000  MHz   Active                 Functional         67108864 67108864
      1     1000  MHz   Idle                   Functional         67108864 67108864
      2     1000  MHz   Idle                   Functional         67108864 67108864
      3     1000  MHz   Idle                   Functional         67108864 67108864

  Central Bus Speed (in MHz)  :        200  
  Available Memory            :   16777212  KB
  Good Memory Required        : Not initialized. Defaults to 32 MB.

   Primary boot path:    0/1/1/0.0           
   Alternate boot path:  0/1/1/0.1           
   Console path:         0/7/1/1.0           
   Keyboard path:        0/0/4/0.0           


Processor is booting from the first available device.

To discontinue, press any key within 10 seconds.

10 seconds expired.
Proceeding...

Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 1


HARD Booted.

ISL Revision A.00.43  Apr 12, 2000

ISL booting  hpux -lq

Boot
: disk(0/1/1/0.0.0.0.0.0.0;0)/stand/vmunix
12136448 + 2310144 + 1777368 start 0x1fff68




alloc_pdc_pages: Relocating PDC from 0xfffffff0f0c00000 to 0x3f901000.



Firmware Version  46.34

Duplex Console IO Dependent Code (IODC) revision 1



Stored message buffer up to panic:
:  SCRATCHF:    00078000
     70:  SCRATCHG:    00000001
     74:  SCRATCHH:    0007d600
     78:  SCRATCHI:    00000000
     7c:  SCRATCHJ:    00000000
     bc:  SCNTL4:    00
    PCI configuration register dump:
                Command: 0157
          Latency Timer: c0
        Cache Line Size: 20

SCSI: Resetting SCSI -- lbolt: 6346, bus: 3 path: 0/1/1/1

SCSI: Reset detected -- lbolt: 6346, bus: 3 path: 0/1/1/1
SCSI: Ultra160 Controller at 0/1/1/1: Error: The domain validation test for target 1 determined that communication may not be possible to this target. Verify the hardware configuration.
SCSI Gross Error on 0/1/1/1:
shadowed SIST0 80 shadowed SIST1 00.
SCSI: isrEscape Controller at 0/1/1/1.

SCSI:  -- lbolt: 6646, bus: 3
        lbp->state: 30008
        lbp->offset: ffffffff
        lbp->nominalOffset: 360
        lbp->Cmdindex: 1
        lbp->last_nexus_index: 0
        lbp->nexus_index: 0
        uCmdSent: 0 uNexus_offset: 0
     last lbp->puStatus [000000004c235600]:
        00000000 00000000 00000000 00000000
     next lbp->puStatus [000000004c2357f0]:
        00000000 00000000 00000000 00000000
    From most recent interrupt:
        ISTAT: 22, SIST0: 08, SIST1: 00, DSTAT: 80, DSPS: 00000000
    lsp: 0x0000000000000000
        DSAtbl->host_iocb_index: 1
        DSAtbl->host_iocb_addr: 7d800
    scratch_lsp: 0x0000000000000000
    c8xx_iocb [ffffffff90010b00]:
        00000000 00000000 00000000 00000000
        00000000 00000000 00000000 00000000
    Pre-DSP script dump [ffffffff90010340]:
        745c0200 00000000 888c0000 fffffd48
        88880000 fffffca8 48000000 00000000
    Script dump [ffffffff90010360]:
        7c5cf000 00000000 7c360000 00000000
        745c3000 00000000 808c2010 fffffe30
    NCR chip register dump for: 0x400200a
     00:  SCNTL3:    77    SCNTL2:    00    SCNTL1:    00    SCNTL0:    ca
     04:  GPREG:    0f    SDID:    00    SXFER:    00    SCID:    47
     08:  SBCL:    00    SSID:    00    SOCL:    00    SFBR:    00
     0c:  SSTAT2:    02    SSTAT1:    00    SSTAT0:    00    DSTAT:    80
     10:  DSA:    90010b00
     14:  MBOX1:    00    MBOX0:    00    ISTAT1:    00    ISTAT:    22
     1c:  TEMP:    00000000
     24:  DCMDDBC:    7c5cf000
     28:  DNAD:    90010360
     2c:  DSP:    90010368
     30:  DSPS:    00000000
     34:  SCRATCHA:    ff000000
     38:  DCNTL:    a1    DWT:    00    DIEN:    7f    DMODE:    4c
     3c:  ADDER:    90010368
     40:  SIST1:    00    SIST0:    08    SIEN1:    97    SIEN0:    8f
     44:  GPCNTL:    2f    MACNTL:    00    SWIDE:    03    SLPAR:    00
     48:  RESPID1:    00    RESPID0:    80    STIME1:    00    STIME0:    fc
     4c:  STEST3:    80    STEST2:    00    STEST1:    0c    STEST0:    07
     50:  RESV50:    00    RESV51:    c0    SIDL1:    fe    SIDL0:    fe
     54:  CCNTL1:    01    CCNTL0:    01    SODL1:    00    SODL0:    00
     58:  RESV58:    00    RESV59:    00    SBDL1:    00    SBDL0:    00
     5c:  SCRATCHB:    00000000
     60:  SCRATCHC:    c0ffffff
     64:  SCRATCHD:    00000000
     68:  SCRATCHE:    90010c00
     6c:  SCRATCHF:    00078000
     70:  SCRATCHG:    00000001
     74:  SCRATCHH:    0007d600
     78:  SCRATCHI:    00000000
     7c:  SCRATCHJ:    00000000
     bc:  SCNTL4:    00
    PCI configuration register dump:
                Command: 0157
          Latency Timer: c0
        Cache Line Size: 20

SCSI: Resetting SCSI -- lbolt: 6746, bus: 3 path: 0/1/1/1

SCSI: Reset detected -- lbolt: 6746, bus: 3 path: 0/1/1/1
SCSI: Ultra160 Controller at 0/1/1/1: Error: The domain validation test for target 1 determined that communication may not be possible to this target. Verify the hardware configuration.
SCSI Gross Error on 0/1/1/1:
shadowed SIST0 80 shadowed SIST1 00.
SCSI: isrEscape Controller at 0/1/1/1.

SCSI:  -- lbolt: 7046, bus: 3
        lbp->state: 30008
        lbp->offset: ffffffff
        lbp->nominalOffset: 360
        lbp->Cmdindex: 1
        lbp->last_nexus_index: 0
        lbp->nexus_index: 0
        uCmdSent: 0 uNexus_of...

System Panic:

linkstamp:          Thu Feb 18 13:57:17 EST 2010
_release_version:   @(#)       $Revision: vmunix:    vw: -proj    selectors: CUPI80_BL2000_1108 -c 'Vw for CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108'  Wed Nov  8 19:24:56 PST 2000 $
panic: I/O system hang

PC-Offset Stack Trace (read across, top of stack is 1st):
  0x002128d8  0x00391ab4  0x00a2d174
  0x00040ca8  0x002677b0  0x0016a32c
  0x0017c804  0x0017a15c
End Of Stack



*** A system crash has occurred.  (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR:  Your system crashed before I/O and dump configuration was complete.
        A crash dump cannot be taken under these circumstances without
        special configuration.  Contact your HP support representative.

4 REPLIES
Torsten.
Acclaimed Contributor

Re: Please help to start HP server

Looks like a bad boot disk.

 

Consider to replace the disk and restore your backup.


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
rvn152
Occasional Visitor

Re: Please help to start HP server

Hello

There are two mirror disks in the system.

System Hardware

    Model:              9000/800/rp3440    
    Main Memory:        16382 MB
    Processors:         4
    Processor(0) Speed: 1000 MHz
    Processor(1) Speed: 1000 MHz
    Processor(2) Speed: 1000 MHz
    Processor(3) Speed: 1000 MHz
    OS mode:            64 bit

Storage devices                  HW Path           Interface          
    TEAC DV-28E-N                    0/0/2/0.0.0.0     IDE Primary Channel
    HP 73.4GST373454LC 70007 Mb      0/1/1/0.1.0       SCSI C1010 Ultra160 Wide LVD
    HP 73.4GST373454LC 70007 Mb      0/1/1/0.0.0       SCSI C1010 Ultra160 Wide LVD

 

I/O Interfaces
    Class          H/W Path       Driver         Description             
    usb            0/0/1/0        hcd            NEC USB Interface   
    usb            0/0/1/1        hcd            NEC USB Interface   
    usb            0/0/1/2        ehci           NEC USB Interface   
    sideba         0/0/2/0        side_ba        CMD IDE controller  
    ext_bus        0/0/2/0.0      side           IDE Primary Channel
    ext_bus        0/0/2/0.1      side           IDE Secondary Channel
    ext_bus        0/1/1/0        c8xx           SCSI C1010 Ultra160 Wide LVD
    ext_bus        0/1/1/1        c8xx           SCSI C1010 Ultra160 Wide LVD
    lan            0/1/2/0        igelan         HP PCI 1000Base-T Core
    fc             0/2/1/0/4/0    fcd            HP A9784-60002 PCI/PCI-X Fibre Channel FC/GigE Combo Adapter (FC Port 1)
    lan            0/2/1/0/6/0    igelan         HP A9784-60002 PCI/PCI-X 1000Base-T FC/GigE Combo Adapter
    fc             0/3/1/0/4/0    fcd            HP A9784-60002 PCI/PCI-X Fibre Channel FC/GigE Combo Adapter (FC Port 1)
    lan            0/3/1/0/6/0    igelan         HP A9784-60002 PCI/PCI-X 1000Base-T FC/GigE Combo Adapter
    lan            0/4/1/0/4/0    btlan          HP A5506B PCI 10/100Base-TX 4 Port
    lan            0/4/1/0/5/0    btlan          HP A5506B PCI 10/100Base-TX 4 Port
    lan            0/4/1/0/6/0    btlan          HP A5506B PCI 10/100Base-TX 4 Port
    lan            0/4/1/0/7/0    btlan          HP A5506B PCI 10/100Base-TX 4 Port
    tty            0/7/1/0        asio0          PCI SimpleComm (103c1290)
    tty            0/7/1/1        asio0          PCI Serial (103c1048)
    ipmi           16             ipmi           IPMI Controller

 

But the error is about "ext_bus        0/1/1/1        c8xx           SCSI C1010 Ultra160 Wide LVD".

 

Torsten.
Acclaimed Contributor

Re: Please help to start HP server

It is much better with more details.

IIRC the external SCSI connector (0/1/1/1) is shared with the top disk slot (0/1/1/1.2).

Any external device connected?

Even a cable only?

Any disk in the top slot?


Hope this helps!
Regards
Torsten.

__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.

__________________________________________________
No support by private messages. Please ask the forum!

If you feel this was helpful please click the KUDOS! thumb below!   
rvn152
Occasional Visitor

Re: Please help to start HP server

Hello

We have put a new disk in the top slot. But it went bad. After we stopped the server and removed the bad disk system could not start.

 

# ioscan -fnC disk

Class     I  H/W Path       Driver  S/W State   H/W Type     Description

=========================================================================

disk      0  0/0/2/0.0.0.0  sdisk   CLAIMED     DEVICE       TEAC    DV-28E-N

                           /dev/dsk/c0t0d0   /dev/rdsk/c0t0d0

disk      1  0/1/1/0.0.0    sdisk   CLAIMED     DEVICE       HP 73.4GST373454LC

                           /dev/dsk/c2t0d0   /dev/rdsk/c2t0d0

disk      2  0/1/1/0.1.0    sdisk   CLAIMED     DEVICE       HP 73.4GST373454LC

                           /dev/dsk/c2t1d0   /dev/rdsk/c2t1d0

disk      3  0/1/1/1.2.0    sdisk   NO_HW       DEVICE       HP 73.4GST373455LC