Problem with HPVM Guest on Blades

[vemana]

Hi All,
I have a HP Blade at 11.23 installed on it.I have installed HPVM sofware Perrier_V350_LR_071012:082726 on it.

From the hpvmconsole when i was trying to boot the HPVM guest i was running into the following problem.

fs0:\> HPUX

(C) Copyright 1999-2006 Hewlett-Packard Development Company, L.P.
All rights reserved

HP-UX Boot Loader for IPF -- Revision 2.029

Press Any Key to interrupt Autoboot
\efi\hpux\AUTO ==> boot vmunix
Seconds left till autoboot - 10
Type 'help' for help

HPUX> boot
> System Memory = 2042 MB
loading section 0
............................................................... (complete)
loading section 1
................ (complete)
loading symbol table
loading System Directory (boot.sys) to MFS
....
loading MFSFILES directory (bootfs) to MFS
.........................
Launching /stand/vmunix
SIZE: Text:31877K + Data:7917K + BSS:5412K = Total:45207K
Console is on Serial COM1
Booting kernel...

Disabling 8259s

Memory Class Setup
-------------------------------------------------------------------------
Class Physmem Lockmem Swapmem
-------------------------------------------------------------------------
System : 2042 MB 2042 MB 2042 MB
Kernel : 2042 MB 2042 MB 2042 MB
User : 1690 MB 1552 MB 1477 MB
-------------------------------------------------------------------------

Loaded ACPI revision 2.0 tables.
NOTICE: cachefs_link(): File system was registered at index 5.
NOTICE: nfs3_link(): File system was registered at index 8.
NOTICE: mod_fs_reg: Cannot retrieve configured loading phase from KRS for module: cifs. Setting to load at INIT

WARNING: wsio_config: The driver UsbBootKeyboard is not present in the kernel. The node at hw path 0/0/2/0.0.0 will remain UNCLAIMED.
WARNING: wsio_config: The driver UsbBootKeyboard is not present in the kernel. The node at hw path 0/0/2/0.0.0 will remain UNCLAIMED.
Boot device's HP-UX HW path is: 0/0/2/0.0.0
iether4: INITIALIZING HP PCI/PCI-X 1000Base-T at hardware path 0/0/0/0
iether5: INITIALIZING HP PCI/PCI-X 1000Base-T at hardware path 0/0/1/0

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
Calling function e0000000011aaf40 for Shutdown State 8 type 0x2

Stored message buffer up to panic:
Found adjacent data tr. Growing size. 0x32f9000 -> 0x72f9000.
Pinned PDK malloc pool: base: 0xe000000100d07000 size=117732K
Loaded ACPI revision 2.0 tables.

MFS is defined: base= 0xe000000100d07000 size= 8068 KB


Unpinned PDK malloc pool: base: 0xe000000108000000 size=81920K
NOTICE: cachefs_link(): File system was registered at index 5.
NOTICE: nfs3_link(): File system was registered at index 8.
NOTICE: mod_fs_reg: Cannot retrieve configured loading phase from KRS for module: cifs. Setting to load at INIT

0 cec_gen
0/0 gh2p
0/0/0/0 iether
0/0/1/0 iether
Initializing the Ultra320 SCSI Controller at 0/0/2/0. Controller firmware version is 00.00.00.00
0/0/2/0 mpt
0/0/3/0 legacyio
0/0/3/0/1 asio0
0/1 gh2p
0/2 gh2p
0/3 gh2p
0/4 gh2p
0/5 gh2p
0/6 gh2p
0/7 gh2p
120 processor
250 pdh
250/0 ipmi
250/1 acpi_node
0/0/2/0.0 tgt
WARNING: wsio_config: The driver UsbBootKeyboard is not present in the kernel. The node at hw path 0/0/2/0.0.0 will remain UNCLAIMED.
0/0/2/0.15 tgt
0/0/2/0.15.0 sctl
WARNING: wsio_config: The driver UsbBootKeyboard is not present in the kernel. The node at hw path 0/0/2/0.0.0 will remain UNCLAIMED.
Boot device's HP-UX HW path is: 0/0/2/0.0.0
iether4: INITIALIZING HP PCI/PCI-X 1000Base-T at hardware path 0/0/0/0
iether5: INITIALIZING HP PCI/PCI-X 1000Base-T at hardware path 0/0/1/0

System Console is on the Built-In Serial Interface
Swap device table: (start & size given in 512-byte blocks)
entry 0 - auto-configured on root device; ignored - can't open device

System Panic:

panic: swapconf - no primary swap space configured
Stack Trace:
IP Function Name
0xe0000000017c3ae0 swapconf+0x3c0
0xe0000000017c7fc0 swaptabinit+0x80
0xe0000000017bff30 swapinit_phasetwo+0x90
0xe0000000017816b0 DoCalllist+0x3a0
End of Stack Trace

linkstamp: Tue Apr 13 15:50:05 IST 2010
_release_version: @(#) $Revision: vmunix: B11.23_LR FLAVOR=perf Fri Aug 29 22:35:38 PDT 2003 $

sync'ing disks (0 buffers to flush): (0 buffers to flush):
0 buffers not flushed
0 buffers still dirty

*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.

ERROR: Your system crashed before I/O and dump configuration was complete.
This system does not support a crash dump under these circumstances.
Contact your HP support representative for assistance.

**** Dumping Guest Image ****

**** Done with dump (6152Kbytes) ****


*** VM restarting ***

.

[vemana]

I have applied all the required HPVM Host patches.

Can somebody please help me?

[melvyn burnard]

Well here is the symptom:
panic: swapconf - no primary swap space configured


You need to verify how you created the install disc, and where/what teh swap was.

[Steven E. Protter]

Shalom,

You were working on your hpvm host, not your guest. The language you used made that fuzzy.

I believe a disk used for the host OS hpvm is missing. Swap is certainly missing.

You are probably going to have to build the host OS over again. Consider HPVM 4.1 or 4.2

4.1 lets you run Windows 2003 IA64 server, or Windows 2008 IA64 server as a guest. 4.2 eliminates support for 2003.

SEP