RX6600 HP-UX_OS_PANIC_SHUTDOWN

[Tihomir Stefanov]

hi,

due to environment power failure our RX6600 went down, and now it doesn't boot HP-UX OS.

Here is system event log from ILO console:

518 Informational System Firmware 0 BOOT_SWITCH_INSECURE_MODE 20 Jul 2010 23:09:18 System has been switched to insecure mode
517 Informational System Firmware 0 BOOT_START 20 Jul 2010 23:08:34 CPU starting boot
516 Informational Redundant w/ an E0 code; CPU_START_BOOT 20 Jul 2010 23:08:34 CPU starting boot
515 Informational Baseboard Management Controller; SOFT_RESET 20 Jul 2010 23:08:24 Soft Reset
514 Warning HP-UX Kernel 0 HP-UX_CRASHDUMP_STARTED 20 Jul 2010 23:08:24 OS crashdump started (D700)
513 Critical HP-UX Kernel 0 HP-UX_HEX_FAULT_CODE 20 Jul 2010 23:08:22 OS legacy PA hex fault code (Bxxx)
512 Fatal System Firmware 6 INIT_INITIATED 20 Jul 2010 23:08:21 INIT initiated
511 Fatal Redundant w/ an E0 code; INIT_INTERRUPT_INITIATED 20 Jul 2010 23:08:20 INIT Initiated
510 Fatal System Firmware 4 INIT_INITIATED 20 Jul 2010 23:08:20 INIT initiated
509 Fatal Redundant w/ an E0 code; INIT_INTERRUPT_INITIATED 20 Jul 2010 23:08:20 INIT Initiated
508 Fatal System Firmware 2 INIT_INITIATED 20 Jul 2010 23:08:20 INIT initiated
507 Fatal Redundant w/ an E0 code; INIT_INTERRUPT_INITIATED 20 Jul 2010 23:08:20 INIT Initiated
506 Fatal HP-UX Kernel 0 HP-UX_OS_PANIC_SHUTDOWN 20 Jul 2010 23:08:19 HP-UX OS shutdown due to a panic
505 Informational System Firmware 0 BOOT_SWITCH_INSECURE_MODE 20 Jul 2010 23:05:30 System has been switched to insecure mode
504 Informational System Firmware 0 BOOT_START 20 Jul 2010 23:04:44 CPU starting boot
503 Informational Redundant w/ an E0 code; CPU_START_BOOT 20 Jul 2010 23:04:44 CPU starting boot
502 Informational Baseboard Management Controller; POWER_UNIT_ENABLED 20 Jul 2010 23:04:31 Power unit enabled


Here are Remote Console messages during boot:

Press Any Key to interrupt Autoboot
\EFI\HPUX\AUTO ==> boot vmunix -lq
Seconds left till autoboot - 0
AUTOBOOTING...> System Memory = 16353 MB
loading section 0
.............................................
(complete)
loading section 1
............... (complete)
loading symbol table
loading System Directory (boot.sys) to MFS
......
loading MFSFILES directory (bootfs) to MFS
.Error - efi_disk_read returned (Device Error)
offser:0x136a000, ma:0xff0c4010, len: 8192
pausing temporarily... 0

Warning: Failed to read all bytes of MFS file: /stand/current/krs/config.krs
.................................
Launching /stand/vmunix
SIZE: Text:40111K + Data:6395K + BSS:19460K = TOTAL:65968K

How to Repair this instalization?

[Basheer_2]

Hello Stefanov,

It says DEVICE Error ( Check the Hard Disk)

OR

If you have an ignite Toape or ignite server, try to repair from that.

[Vijaykumar_1]

Hi,

The error seems that the file "/stand/current/krs/config.krs" is unreadable.

This means that the system file is not in sysn with the booted kernel.

Booting into single usermode and performing an fsck would help you resolve the issue.

[Vijaykumar_1]

>This means that the system file is not in SYNC* with the booted kernel