- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - Linux
- >
- Re: Recreating a logical drive with SmartStart CD
Operating System - Linux
1753805
Members
7551
Online
108805
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-08-2010 08:08 AM
12-08-2010 08:08 AM
Recreating a logical drive with SmartStart CD
I have a HP Proliant DL380 G4 running RHEL AS3. The server has two logical drives. The second logical drive consists of two disks and mirror each other so its setup RAID 1.
My problem is that both disks are showing a "Red light" to indicate a fault. I am aware this means there is going to some data loss. I have reseated both disks and the "Red Light" has cleared.
When I reboot the HP Proliant DL380 server the system automatically ran "fsck" to fix bad block errors in the mirror set.
I have a good backup of the file system so I can restore the file system.
I want to know if I did replace the two physical disks in the mirror, would I need the Smartstart CD to recreate the logical drve as mirror (Raid 1) and if so how?
Thank you
My problem is that both disks are showing a "Red light" to indicate a fault. I am aware this means there is going to some data loss. I have reseated both disks and the "Red Light" has cleared.
When I reboot the HP Proliant DL380 server the system automatically ran "fsck" to fix bad block errors in the mirror set.
I have a good backup of the file system so I can restore the file system.
I want to know if I did replace the two physical disks in the mirror, would I need the Smartstart CD to recreate the logical drve as mirror (Raid 1) and if so how?
Thank you
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
12-08-2010 09:40 AM
12-08-2010 09:40 AM
Re: Recreating a logical drive with SmartStart CD
You can do so via the BIOS/Smart Array Controller's Firmware OR via the OS's hpacutil utility.
It should be very straightforwardy either way.
It should be very straightforwardy either way.
Hakuna Matata.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP