Reg : dmesg output - suggestions

[Mastan]

Hai,

We have hp-ux rx2620 server and in front panel orange led is blinking, I have posted below dmesg output.

Please let me know any suggestions.

# dmesg
Feb 17 10:09
Found adjacent data tr. Growing size. 0x31b2000 -> 0x71b2000.
Pinned PDK malloc pool: base: 0xe000000100e4e000 size=116424K
Loaded ACPI revision 2.0 tables.
MFS is defined: base= 0xe000000100e4e000 size= 7452 KB
Unpinned PDK malloc pool: base: 0xe000000108000000 size=180224K
NOTICE: cachefs_link(): File system was registered at index 4.
NOTICE: nfs3_link(): File system was registered at index 7.
LLT INFO V-14-1-10009 LLT Protocol available
GAB INFO V-15-1-20021 GAB available
vxfen: vxfen protocol available
LMX: LMX Protocol available
VCSMM: VCSMM Available
0 sba
0/0 lba
0/0/1/0 UsbOhci
0/0/1/1 UsbOhci
0/0/1/2 UsbEhci
0/0/2/0 side_multi
0/0/2/0.0 side
0/0/2/0.0.0 tgt
0/0/2/0.0.0.0 sdisk
0/0/2/0.0.7 tgt
0/0/2/0.0.7.0 sctl
0/0/2/0.1 side
0/0/2/0.1.7 tgt
0/0/2/0.1.7.0 sctl
0/1 lba
Initializing the Ultra320 SCSI Controller at 0/1/1/0. Controller firmware version is 01.03.35.65
0/1/1/0 mpt
SCSI Ultra320 0/1/1/0 instance 2: The driver is now online
0/1/1/0.0 tgt
0/1/1/0.0.0 sdisk
0/1/1/0.1 tgt
0/1/1/0.1.0 sdisk
Initializing the Ultra320 SCSI Controller at 0/1/1/1. Controller firmware version is 01.03.35.65
0/1/1/1 mpt
0/1/2/0 iether
0/1/2/1 iether
0/2 lba
0/3 lba
0/3/1/0 td
SCSI Ultra320 0/1/1/1 instance 3: The driver is now online
0/1/1/0.7 tgt
0/1/1/0.7.0 sctl
td: claimed Tachyon XL2 Fibre Channel Mass Storage card at 0/3/1/0
0/4 lba
0/4/1/0 igelan
0/5 lba
0/6 lba
0/6/1/0 asio0
0/6/1/1 asio0
0/6/2/0 gvid_core
120 processor
121 processor
250 pdh
250/0 ipmi
250/1 asio0
250/2 asio0
250/3 acpi_node
0/3/1/0.1 fcp
0/3/1/0.1.0.255.0 fcpdev
0/3/1/0.1.2.255.0 fcpdev
0/3/1/0.1.0.255.0.0 tgt
0/3/1/0.1.2.255.0.0 tgt
0/3/1/0.1.2.255.0.0.0 sdisk
0/3/1/0.1.2.255.0.0.1 sdisk
0/3/1/0.1.0.255.0.0.0 stape
0/3/1/0.1.2.255.0.0.2 sdisk
0/3/1/0.1.2.255.0.0.3 sdisk
0/3/1/0.1.2.255.0.0.4 sdisk
0/3/1/0.1.2.255.0.0.5 sdisk
0/3/1/0.1.2.255.0.0.6 sdisk
0/3/1/0.1.2.255.0.0.7 sdisk
0/1/1/1.7 tgt
0/1/1/1.7.0 sctl
Boot device's HP-UX HW path is: 0/1/1/0.1.0
iether0: INITIALIZING HP PCI-X 1000Base-T Dual-port Built-in at hardware path 0/1/2/0
iether1: INITIALIZING HP PCI-X 1000Base-T Dual-port Built-in at hardware path 0/1/2/1
igelan2: INITIALIZING HP A6825-60101 PCI 1000Base-T Adapter at hardware path 0/4/1/0
System Console is on the Built-In Serial Interface
Logical volume 64, 0x3 configured as ROOT
Logical volume 64, 0x2 configured as SWAP
Logical volume 64, 0x2 configured as DUMP
Swap device table: (start & size given in 512-byte blocks)
entry 0 - major is 64, minor is 0x2; start = 0, size = 32768000
Dump device table: (start & size given in 1-Kbyte blocks)
entry 0000000000000000 - major is 31, minor is 0x21000; start = 1055604, size = 16383996
Starting the STREAMS daemons-phase 1
Create STCP device files
Starting the STREAMS daemons-phase 2
$Revision: vmunix: B11.23_LR FLAVOR=perf Fri Aug 29 22:35:38 PDT 2003 $
Memory Information:
physical page size = 4096 bytes, logical page size = 4096 bytes
Physical: 8377112 Kbytes, lockable: 6027700 Kbytes, available: 7021304 Kbyte
NOTICE: MOD: modld: Module already loaded
NOTICE: MOD: modld: Module already loaded
NOTICE: MOD: modld: Module already loaded
NOTICE: MOD: modld: Module already loaded
NOTICE: MOD: modld: Module already loaded
NOTICE: VxVM vxdmp V-5-0-34 added disk array 75010402, datype = AMS_WMS

NOTICE: VxVM vxdmp V-5-0-34 added disk array DISKS, datype = Disk

NOTICE: VxVM vxdmp V-5-3-1700 dmpnode 0/0x0 has migrated from enclosure FAKE_ENCLR_SNO to enclosure DISKS

GAB WARNING V-15-1-20115 Port d registration failed, GAB not configured
vxgms: GAB_API_REGISTER error=261
ODM WARNING V-41-6-5 odm_gms_api_start_msgs fails

Thanks & Regards,
Mastan.

[nijokj]

Plaese refer the below document and find out
which LED on the front panel flashing orange and corresponding troubleshooting information.

http://bizsupport.austin.hp.com/bc/docs/support/SupportManual/c01404139/c01404139.pdf

[shanmuhanandam]

Hi,
hope you have the MP access. login to the MP and type sl, then select the system event (E), read the message. If the alert level is less than 2, you can ignore it. Or else log a case with support provider.
Once you view the event, then the LED will blink as green.

Thanks,
Shan.