- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- STM output for disk read/write error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-24-2009 05:31 AM
тАО06-24-2009 05:31 AM
STM output for disk read/write error
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-24-2009 05:37 AM
тАО06-24-2009 05:37 AM
Re: STM output for disk read/write error
I don't want any read-write errors on a disk. Zero.
I would run some further tests, get a backup done and preemptively replace the disk. If the disk is merely busy, I might decide otherwise.
http://docs.hp.com/en/7161/LVM_OLR_whitepaper.pdf
That document is the holy grail on this subject.
SEP
Owner of ISN Corporation
http://isnamerica.com
http://hpuxconsulting.com
Sponsor: http://hpux.ws
Twitter: http://twitter.com/hpuxlinux
Founder http://newdatacloud.com
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-24-2009 05:42 AM
тАО06-24-2009 05:42 AM
Re: STM output for disk read/write error
Have a look at the doc below .It will tell you all the ways to diagnose and replace the disks.
http://docs.hp.com/en/5991-1236/When_Good_Disks_Go_Bad_WP.pdf
Regards
Vivek Bhatia
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-24-2009 06:05 AM
тАО06-24-2009 06:05 AM
Re: STM output for disk read/write error
If you suspect any disk i/o error, run dd to check the consistency. If errors are there, replace it without second thought.
Example:
# dd if=/dev/rdsk/c1t5d0 of=/dev/null bs=1024k
Ganesh.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-24-2009 06:38 AM
тАО06-24-2009 06:38 AM