- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: Switch to tty in hp ux
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2009 12:54 AM
тАО02-06-2009 12:54 AM
Switch to tty in hp ux
While i was executing swcopy command wireless connection on my laptop got disconnected, after restoring network after 5 mints putty section i have to restart and after login how do I get into old tty.
# w
2:17pm up 98 days, 22:34, 5 users, load average: 0.01, 0.02, 0.02
User tty login@ idle JCPU PCPU what
root pts/0 9:20am 2:47 -sh
admin pts/1 2:07pm 8 24 24 swcopy -s /cdrom * @ /home/11iv3/update-depot
admin pts/2 2:10pm 6 -sh
admin pts/3 2:14pm 3 -sh
admin pts/4 2:15pm w
As shown above i was on pts/1 there we can see swcopy is running.
Now I am in pts/4.
Please advice me how to switch to pts/1 so that I will get swcopy output after execution.
Thamks & Regards
Yash
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2009 01:05 AM
тАО02-06-2009 01:05 AM
Re: Switch to tty in hp ux
if you were using putty and not logged in through the console, and you didn't use nohup
to run swcopy command,
then my guess is that that session is not doing much anymore.
Best to kill it and start again.
This time use eiter
1)nohup swcopy -s /cdrom * @ /home/11iv3/update-depot &
2) login on the console port
good luck
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2009 01:09 AM
тАО02-06-2009 01:09 AM
Re: Switch to tty in hp ux
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2009 01:23 AM
тАО02-06-2009 01:23 AM
Re: Switch to tty in hp ux
Thanks
Do I need to kill that session?
Now that session is not present (pts/1).
I can see size of /home/11iv3/update-depot is increasing.
swcopy process is still running right.
do i need to run swcopy once agian or wait ?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2009 01:38 AM
тАО02-06-2009 01:38 AM
Re: Switch to tty in hp ux
As you see that is incresing in size so perhaps the depot is getting copied.
So can wait for a while and see.
regards
Sujit
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-06-2009 02:05 AM
тАО02-06-2009 02:05 AM
Re: Switch to tty in hp ux
Do you know how long it takes? Are you close to the beginning or the end? :-)
You can use swlist to see what's there when it finishes. And swverify to make sure it is ok.