- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- aggregation
Operating System - HP-UX
1753868
Members
7057
Online
108809
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-15-2010 05:30 AM
10-15-2010 05:30 AM
aggregation
I want to connect my rx2660 to our netapp storage with iscsi.
I have 2 lan ports connected to a vlan where the netapp also is in.
Both of the cards have ip addresses in the same network.
What port will be used now and how do I see that?
Can I make an aggregate for these two card and how do I do that?
Thanks in advance.
I have 2 lan ports connected to a vlan where the netapp also is in.
Both of the cards have ip addresses in the same network.
What port will be used now and how do I see that?
Can I make an aggregate for these two card and how do I do that?
Thanks in advance.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-15-2010 08:25 AM
10-15-2010 08:25 AM
Re: aggregation
Hi,
Yes u can make auto port aggregate for these two cards.
Both of the card should be in different vlan,
Check the linkloop test of both the lan cards.
OS should be HPUX 11iV3 or V2
Install the APA depot and configure.
Please refer below thread
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1434570
Hope this solves ur query
Regards
Vishnu Khandare
Yes u can make auto port aggregate for these two cards.
Both of the card should be in different vlan,
Check the linkloop test of both the lan cards.
OS should be HPUX 11iV3 or V2
Install the APA depot and configure.
Please refer below thread
http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=1434570
Hope this solves ur query
Regards
Vishnu Khandare
You should deserve before U desire!!!!
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP