cmviewcl not working for normal user,

[jeevarajkn]

Dear Guru's

OS--HP UX 11.23--rx6600

I am not able to excute the cmviewcl command by using normal user.

Permission denied to 127.0.0.1
cmviewcl: Cannot view the cluster configuration: Permission denied.
This user doesn't have access to view the cluster configuration.



I already add the entry in /etc/cmcluster/cmclnodelist.

But still problem existing.

Can anybody help me...

[Ivan Krastev]

Is your syntax correct, as described here - http://docs.hp.com/en/B5158-90024/ch05s01.html

Format is :
hostname username

regards,
ivan

[vjta]

Hi jeeva
can u post ur cmclnodelist contents here

you can add
hostname or
+
for other users

regards
vjta

[Jeeshan]

check this relevant link

http://forums11.itrc.hp.com/service/forums/questionanswer.do?threadId=971667

[Duncan Edmonstone · Accepted solution]

I'm going to make 2 assumptions based on what you've told us:

i) cmviewcl *does* work for the root user
ii) this node is already configured into a Serviceguard cluster

Serviceguard ignores the cmclnodelist file once the cluster node is configured and you then need to define rols in the package configuration files. This is described in the manual here:

http://docs.hp.com/en/B3936-90117/ch05s01.html#cacjcidg

scroll down to the section titled "Setting Access Controls for Configured Cluster Nodes"

HTH

Duncan

[Avinash20]

<<< I am not able to excute the cmviewcl command by using normal user. >>> ??

Jeevan: It is working fine for the root user ??
If not, then
Please see that nslookup to hostname or fully qualified domain names works.

Eg: If A and B are two nodes, then see that

# nslookup A
# nslookup B

## The above command gives the correct IP address on both the nodes

# nslookup
# nslookup

## The above commands resolves to the correct hostname on both the nodes

[jeevarajkn]

Hi All

This is my cmclnodelist entry in both nodes.

uaedxbpdctakp02>more /etc/cmcluster/cmclnodelist
uaedxbpdctakp01 root
uaedxbpdctakp02 root
uaedxbpdctakp01 uxgsmc
uaedxbpdctakp02 uxgsmc

But in my other cluster nodes this user can able to run cmviewcl with out this entry in cmclnodlist.

[Duncan Edmonstone]

So you're going to ignore my repsonse are you? It seems from what you are saying that you already have a running cluster. As I stated in my previous post, cmclnodelist is completely ignored once a cluster is created (i.e. the binary file /etc/cmcluster/cmclconfig exists).

From this point on you need to make sure you have the required entries for cluster or package admin, or just for monitoring in your cluster/package configurations. As described in the manual I pointed you at.

HTH

Duncan

[jeevarajkn]

Duncan,

Can you plesae confirm in which file I want to give the entry.

In my /etc/cmcluster/cmclconfig i didn't find any option but same time i found in /etc/cmcluster/pkg1/pkg1.conf file where my package name is pkg1.

I given the below entry in /etc/cmcluster/pkg1/pkg1.conf of both nodes.

USER_NAME ANY_USER
USER_HOST CLUSTER_MEMBER_NODE
USER_ROLE package_admin

But it didn't solve my issue...

[Duncan Edmonstone]

So you put the entries in the package configuration file, but did you check/apply the configuration using cmcheckconf -P ... and cmapplyconf -P ...

HTH

Duncan