System Administration
cancel
Showing results for 
Search instead for 
Did you mean: 

es4100 crash when boot up trap: invalid memory read access from kernel mode

邹英琼_1
Occasional Contributor

es4100 crash when boot up trap: invalid memory read access from kernel mode

Compaq Tru64 UNIX P5.1A (Rev. 646); Sat Jan 25 03:26:26 EST 2003
Aug 22 13:03:37 scserver1 vmunix: physical memory = 2048.00 megabytes.
Aug 22 13:03:37 scserver1 vmunix: available memory = 1983.47 megabytes.
Aug 22 13:03:37 scserver1 vmunix: using 7784 buffers containing 60.81 megabytes of memory
Aug 22 13:03:37 scserver1 vmunix: Master cpu at slot 0
Aug 22 13:03:37 scserver1 vmunix: Starting secondary cpu 1
Aug 22 13:03:37 scserver1 vmunix: Firmware revision: 6.0
Aug 22 13:03:37 scserver1 vmunix: PALcode: UNIX version 1.23
Aug 22 13:03:37 scserver1 vmunix: AlphaServer 4100 5/533 4MB
Aug 22 13:03:37 scserver1 vmunix: pci1 (primary bus:1) at mcbus0 slot 5
Aug 22 13:03:37 scserver1 vmunix: Loading SIOP: script c0000000, reg 7faee00, data c000a000
Aug 22 13:03:37 scserver1 vmunix: scsi0 at psiop0 slot 0 rad 0
Aug 22 13:03:37 scserver1 vmunix: isp0 at pci1 slot 2
Aug 22 13:03:37 scserver1 vmunix: isp0: QLOGIC ISP1040B/V2
Aug 22 13:03:37 scserver1 vmunix: isp0: Firmware revision 5.57 (loaded by console)
Aug 22 13:03:37 scserver1 vmunix: isp0: Fast RAM timing enabled.
Aug 22 13:03:37 scserver1 vmunix: scsi1 at isp0 slot 0 rad 0
Aug 22 13:03:37 scserver1 vmunix: tu0: DECchip 21143: Revision: 3.0
Aug 22 13:03:37 scserver1 vmunix: tu0: auto negotiation capable device
Aug 22 13:03:37 scserver1 vmunix: tu0 at pci1 slot 4
Aug 22 13:03:37 scserver1 vmunix: tu0: DEC TULIP (10/100) Ethernet Interface, hardware address: 08-00-2B-C4-65-03
Aug 22 13:03:37 scserver1 vmunix: tu0: auto negotiation off: selecting 10BaseT (UTP) port: half duplex
Aug 22 13:03:37 scserver1 vmunix: pci0 (primary bus:0) at mcbus0 slot 4
Aug 22 13:03:37 scserver1 vmunix: eisa0 at pci0
Aug 22 13:03:37 scserver1 vmunix: ace0 at eisa0
Aug 22 13:03:37 scserver1 vmunix: ace1 at eisa0
Aug 22 13:03:37 scserver1 vmunix: comet0: Card type 'Elsa GLoria' with 8MB framebuffer memory.
Aug 22 13:03:37 scserver1 vmunix: comet0 at pci0 slot 2
Aug 22 13:03:37 scserver1 vmunix: mchan0: Module revision = 35
Aug 22 13:03:37 scserver1 vmunix: mchan0: jumpered as VH0 configuration
Aug 22 13:03:37 scserver1 vmunix: mchan0 at pci0 slot 3
Aug 22 13:03:37 scserver1 vmunix: emx0 at pci0 slot 4
Aug 22 13:03:37 scserver1 vmunix: KGPSA-BC : Driver Rev 2.06 : F/W Rev 3.03A1(1.31) : wwn 1000-0000-c922-553c
Aug 22 13:03:37 scserver1 vmunix: emx0: Using console topology setting of : Fabric
Aug 22 13:03:37 scserver1 vmunix: scsi2 at emx0 slot 0 rad 0
Aug 22 13:03:37 scserver1 vmunix: Created FRU table binary error log packet
Aug 22 13:03:37 scserver1 vmunix: kernel console: ace0
Aug 22 13:03:37 scserver1 vmunix: i2c: Server Management Hardware Present
Aug 22 13:03:37 scserver1 vmunix: dli: configured
Aug 22 13:03:37 scserver1 vmunix: NetRAIN configured.
Aug 22 13:03:37 scserver1 vmunix: TruCluster Server V5.1A (Rev. 1312); 01/25/03 02:08
Aug 22 13:03:37 scserver1 vmunix: TNC kproc_creator_daemon: Initialized and Ready
Aug 22 13:03:37 scserver1 vmunix: clubase: configured
Aug 22 13:03:37 scserver1 vmunix: Configuring RDG to use Memory Channel
Aug 22 13:03:37 scserver1 vmunix: ics_hl: Configuring memory channel as transport.
Aug 22 13:03:37 scserver1 vmunix: icsnet: configured
Aug 22 13:03:37 scserver1 vmunix: drd configured 0
Aug 22 13:03:37 scserver1 vmunix: kch: configured
Aug 22 13:03:37 scserver1 vmunix: dlm: configured
Aug 22 13:03:37 scserver1 vmunix: Starting CFS daemons
Aug 22 13:03:37 scserver1 vmunix: Registering CFS Services
Aug 22 13:03:37 scserver1 vmunix: Initializing CFSREC ICS Service
Aug 22 13:03:37 scserver1 vmunix: Registering CFSMSFS remote syscall interface
Aug 22 13:03:37 scserver1 vmunix: Registering CMS Services
Aug 22 13:03:37 scserver1 vmunix: rm slave: mchan0, hubslot = 0, phys_rail 0 (size 128 MB)
Aug 22 13:03:37 scserver1 vmunix: rm slave: log_rail 0 (size 128 MB), phys_rail 0 (mchan0)
Aug 22 13:03:37 scserver1 vmunix: ics_mct: icsinfo set for node 1
Aug 22 13:03:37 scserver1 vmunix: ics_mct: Declaring this node up 1
Aug 22 13:03:37 scserver1 vmunix: ics_mct: icsinfo set for node 2
Aug 22 13:03:37 scserver1 vmunix: CNX MGR: Join operation complete
Aug 22 13:03:37 scserver1 vmunix: CNX MGR: membership configuration index: 2 (2 additions, 0 removals)
Aug 22 13:03:37 scserver1 vmunix: CNX MGR: quorum (re)gained, (re)starting cluster operations.
Aug 22 13:03:37 scserver1 vmunix: Joining versw kch set.
Aug 22 13:03:37 scserver1 vmunix: CNX MGR: Node scserver1 1 incarn 0x563a8 csid 0x10002 has been added to the cluster
Aug 22 13:03:37 scserver1 vmunix: ics_mct: Declaring this node up 2
Aug 22 13:03:37 scserver1 vmunix: CNX MGR: Node scserver2 2 incarn 0xe3903 csid 0x10001 has been added to the cluster
Aug 22 13:03:37 scserver1 vmunix: dlm: resuming lock activity
Aug 22 13:03:37 scserver1 vmunix: kch: resuming activity
Aug 22 13:03:37 scserver1 vmunix: clsm: incoming CNX data: '卆 '
Aug 22 13:03:37 scserver1 vmunix: clsm: checking for peer configurations
Aug 22 13:03:37 scserver1 vmunix: clsm: initialized
Aug 22 13:03:37 scserver1 vmunix: Waiting for cluster mount to complete
Aug 22 13:03:37 scserver1 vmunix: vm_swap_init: swap is set to eager allocation mode
Aug 22 13:03:37 scserver1 vmunix: CMS: Joining deferred filesystem sets
Aug 22 13:03:37 scserver1 vmunix: CNX QDISK: Successfully claimed quorum disk, adding 1 vote.
Aug 22 13:04:09 scserver1 vmunix: cluster alias subsystem enabled
Aug 22 13:04:19 scserver1 vmunix: Environmental Monitoring Subsystem Configured.
Aug 22 13:17:26 scserver1 vmunix: Alpha boot: available memory from 0x3e44000 to 0x7fff6000
Aug 22 13:17:26 scserver1 vmunix: Compaq Tru64 UNIX V5.1A (Rev. 1885); Mon Aug 22 13:07:51 CST 2005
Aug 22 13:17:26 scserver1 vmunix: physical memory = 2048.00 megabytes.
Aug 22 13:17:26 scserver1 vmunix: available memory = 1985.69 megabytes.
Aug 22 13:17:26 scserver1 vmunix: using 7793 buffers containing 60.88 megabytes of memory
Aug 22 13:17:26 scserver1 vmunix: Master cpu at slot 0
Aug 22 13:17:26 scserver1 vmunix: Starting secondary cpu 1
Aug 22 13:17:26 scserver1 vmunix: Firmware revision: 6.0
Aug 22 13:17:26 scserver1 vmunix: PALcode: UNIX version 1.23
Aug 22 13:17:26 scserver1 vmunix: AlphaServer 4100 5/533 4MB
Aug 22 13:17:26 scserver1 vmunix: pci1 (primary bus:1) at mcbus0 slot 5
Aug 22 13:17:26 scserver1 vmunix: Loading SIOP: script c0000000, reg 7faee00, data c000a000
Aug 22 13:17:26 scserver1 vmunix: scsi0 at psiop0 slot 0 rad 0
Aug 22 13:17:26 scserver1 vmunix: isp0 at pci1 slot 2
Aug 22 13:17:26 scserver1 vmunix: isp0: QLOGIC ISP1040B/V2
Aug 22 13:17:26 scserver1 vmunix: isp0: Firmware revision 5.57 (loaded by console)
Aug 22 13:17:26 scserver1 vmunix: isp0: Fast RAM timing enabled.
Aug 22 13:17:26 scserver1 vmunix: scsi1 at isp0 slot 0 rad 0
Aug 22 13:17:26 scserver1 vmunix: tu0: DECchip 21143: Revision: 3.0
Aug 22 13:17:26 scserver1 vmunix: tu0: auto negotiation capable device
Aug 22 13:17:26 scserver1 vmunix: tu0 at pci1 slot 4
Aug 22 13:17:26 scserver1 vmunix: tu0: DEC TULIP (10/100) Ethernet Interface, hardware address: 08-00-2B-C4-65-03
Aug 22 13:17:26 scserver1 vmunix: tu0: auto negotiation off: selecting 10BaseT (UTP) port: half duplex
Aug 22 13:17:26 scserver1 vmunix: pci0 (primary bus:0) at mcbus0 slot 4
Aug 22 13:17:26 scserver1 vmunix: eisa0 at pci0
Aug 22 13:17:26 scserver1 vmunix: ace0 at eisa0
Aug 22 13:17:26 scserver1 vmunix: ace1 at eisa0
Aug 22 13:17:26 scserver1 vmunix: comet0: Card type 'Elsa GLoria' with 8MB framebuffer memory.
Aug 22 13:17:26 scserver1 vmunix: comet0 at pci0 slot 2
Aug 22 13:17:26 scserver1 vmunix: mchan0: Module revision = 35
Aug 22 13:17:26 scserver1 vmunix: mchan0: jumpered as VH0 configuration
Aug 22 13:17:26 scserver1 vmunix: mchan0 at pci0 slot 3
Aug 22 13:17:26 scserver1 vmunix: emx0 at pci0 slot 4
Aug 22 13:17:26 scserver1 vmunix: KGPSA-BC : Driver Rev 2.06 : F/W Rev 3.03A1(1.31) : wwn 1000-0000-c922-553c
Aug 22 13:17:26 scserver1 vmunix: emx0: Using console topology setting of : Fabric
Aug 22 13:17:26 scserver1 vmunix: scsi2 at emx0 slot 0 rad 0
Aug 22 13:17:26 scserver1 vmunix: Created FRU table binary error log packet
Aug 22 13:17:26 scserver1 vmunix: kernel console: ace0
Aug 22 13:17:26 scserver1 vmunix: dli: configured
Aug 22 13:17:26 scserver1 vmunix: NetRAIN configured.
Aug 22 13:17:26 scserver1 vmunix: ATM Subsystem configured with 2 restart threads
Aug 22 13:17:26 scserver1 vmunix: ATMUNI: configured
Aug 22 13:17:26 scserver1 vmunix: ATMSIG: 3.x (module=uni3x) configured
Aug 22 13:17:26 scserver1 vmunix: ILMI: 3.x (module=ilmi) configured
Aug 22 13:17:26 scserver1 vmunix: ATM IP: configured
Aug 22 13:17:26 scserver1 vmunix: ATM LANE: configured.
Aug 22 13:17:26 scserver1 vmunix: ATM IFMP: configured
Aug 22 13:17:26 scserver1 vmunix: TruCluster Server V5.1A (Rev. 1312); 01/25/03 02:08
Aug 22 13:17:26 scserver1 vmunix: TNC kproc_creator_daemon: Initialized and Ready
Aug 22 13:17:26 scserver1 vmunix: clubase: configured
Aug 22 13:17:26 scserver1 vmunix: Configuring RDG to use Memory Channel
Aug 22 13:17:26 scserver1 vmunix: ics_hl: Configuring memory channel as transport.
Aug 22 13:17:26 scserver1 vmunix: icsnet: configured
Aug 22 13:17:26 scserver1 vmunix: drd configured 0
Aug 22 13:17:26 scserver1 vmunix: kch: configured
Aug 22 13:17:26 scserver1 vmunix: dlm: configured
Aug 22 13:17:26 scserver1 vmunix: Starting CFS daemons
Aug 22 13:17:26 scserver1 vmunix: Registering CFS Services
Aug 22 13:17:26 scserver1 vmunix: Initializing CFSREC ICS Service
Aug 22 13:17:26 scserver1 vmunix: Registering CFSMSFS remote syscall interface
Aug 22 13:17:26 scserver1 vmunix: i2c: Server Management Hardware Present
Aug 22 13:17:26 scserver1 vmunix: Registering CMS Services
Aug 22 13:17:26 scserver1 vmunix: rm slave: mchan0, hubslot = 0, phys_rail 0 (size 128 MB)
Aug 22 13:17:26 scserver1 vmunix: rm slave: log_rail 0 (size 128 MB), phys_rail 0 (mchan0)
Aug 22 13:17:26 scserver1 vmunix: ics_mct: icsinfo set for node 1
Aug 22 13:17:26 scserver1 vmunix: ics_mct: Declaring this node up 1
Aug 22 13:17:26 scserver1 vmunix: ics_mct: icsinfo set for node 2
Aug 22 13:17:26 scserver1 vmunix: CNX MGR: Join operation complete
Aug 22 13:17:26 scserver1 vmunix: CNX MGR: membership configuration index: 4 (3 additions, 1 removals)
Aug 22 13:17:26 scserver1 vmunix: CNX MGR: quorum (re)gained, (re)starting cluster operations.
Aug 22 13:17:26 scserver1 vmunix: Joining versw kch set.
Aug 22 13:17:26 scserver1 vmunix: CNX MGR: Node scserver1 1 incarn 0xa13d0 csid 0x20002 has been added to the cluster
Aug 22 13:17:26 scserver1 vmunix: ics_mct: Declaring this node up 2
Aug 22 13:17:26 scserver1 vmunix: CNX MGR: Node scserver2 2 incarn 0xe3903 csid 0x10001 has been added to the cluster
Aug 22 13:17:26 scserver1 vmunix: dlm: resuming lock activity
Aug 22 13:17:26 scserver1 vmunix: kch: resuming activity
Aug 22 13:17:26 scserver1 vmunix: cam_logger: SCSI event packet
Aug 22 13:17:26 scserver1 vmunix: cam_logger: bus 1
Aug 22 13:17:26 scserver1 vmunix: isp_reinit
Aug 22 13:17:26 scserver1 vmunix: clsm: incoming CNX data: '卆 '
Aug 22 13:17:26 scserver1 vmunix: Beginning Adapter/Chip reinitialization (0x1)
Aug 22 13:17:26 scserver1 vmunix: cam_logger: SCSI event packet
Aug 22 13:17:26 scserver1 vmunix: cam_logger: bus 1
Aug 22 13:17:26 scserver1 vmunix: isp_cam_bus_reset_tmo
Aug 22 13:17:26 scserver1 vmunix: SCSI Bus Reset performed
Aug 22 13:17:26 scserver1 vmunix: clsm: checking for peer configurations
Aug 22 13:17:26 scserver1 vmunix: clsm: initialized
Aug 22 13:17:26 scserver1 vmunix: Waiting for cluster mount to complete
Aug 22 13:17:26 scserver1 vmunix: vm_swap_init: swap is set to eager allocation mode
Aug 22 13:17:26 scserver1 vmunix: CMS: Joining deferred filesystem sets
Aug 22 13:17:26 scserver1 vmunix: CNX QDISK: Successfully claimed quorum disk, adding 1 vote.
Aug 22 13:17:32 scserver1 vmunix: cluster alias subsystem enabled
Aug 22 13:17:43 scserver1 vmunix: Environmental Monitoring Subsystem Configured.
Aug 22 13:17:46 scserver1 vmunix:
Aug 22 13:17:46 scserver1 vmunix: trap: invalid memory read access from kernel mode
Aug 22 13:17:46 scserver1 vmunix:
Aug 22 13:17:46 scserver1 vmunix: faulting virtual address: 0x0000000000000010
Aug 22 13:17:46 scserver1 vmunix: pc of faulting instruction: 0xfffffc00007c683c
Aug 22 13:17:46 scserver1 vmunix: ra contents at time of fault: 0xfffffc000083e8bc
Aug 22 13:21:28 scserver1 vmunix: sp contents at time of fault: 0xfffffe04a1e4f230
Aug 22 13:21:28 scserver1 vmunix:
Aug 22 13:21:28 scserver1 vmunix: panic (cpu 0): kernel memory fault
Aug 22 13:21:28 scserver1 vmunix: syncing disks...
9 REPLIES
邹英琼_1
Occasional Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

i test my hardware ,no problem from in my computer .

os: 5.1a, trucluster 5.1,DATABASE:ORACLE
Ross Minkov
Esteemed Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

From SRM try:

>>> test

did you see any problems reported?

>>> show memory

did you see all of the memory you had reported?

-Ross
邹英琼_1
Occasional Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

i test my memory ,is good ,

>>> test

no errolg found .

>>>show memeory

is ok ,no error found .

Venkatesh BL
Honored Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

Did you try booting through 'genvmunix'? May be the crash files in /var/adm/crash would have some useful info.
Michael Schulte zur Sur
Honored Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

Hi,

what version is your patch kit?

greetings,

Michael
Ivan Ferreira
Honored Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

Are you able to boot in single user mode?

boot -fl s

Are you able to boot one node at the time?
Por que hacerlo dificil si es posible hacerlo facil? - Why do it the hard way, when you can do it the easy way?
Aaron Biver_2
Frequent Advisor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

please post the stack trace. This can be obtained this way, for example:

# ksh
# dbx -k /var/adm/crash/vm*.$((`cat bounds` - 1)) <t
q
EOF
(this runs dbx on the most recent crashdump, gets the stack trace, then quits)
Martin Moore
HPE Pro

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

Your EISA configuration information in NVRAM might be corrupt. This is particularly likely if you've recently upgraded the o/s or firmware on the system.

Try re-running the ECU (EISA Configuration Utility). Just bring it up, do "Save & Exit", then power-cycle the system and try to boot it.

Martin
I work for HP
A quick resolution to technical issues for your HP Enterprise products is just a click away HP Support Center Knowledge-base
See Self Help Post for more details

Ralf Puchner
Honored Contributor

Re: es4100 crash when boot up trap: invalid memory read access from kernel mode

a "invalid memory read access from kernel mode" is not hardware related. A crash analyze without a crash-data file is useless and if the crash-data file does not contain known issues you must provide the crash itself and vmzcore.

But a crash analyze need time and knowledge, so please open a call within the HP support center.
Help() { FirstReadManual(urgently); Go_to_it;; }