- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - HP-UX
- >
- Re: insf -e hangs (HP-UX 11.11i v1)
Operating System - HP-UX
1753633
Members
6163
Online
108798
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-12-2009 03:39 PM
09-12-2009 03:39 PM
insf -e hangs (HP-UX 11.11i v1)
We have moved our Primary SAN switch and it the process we changed the ports used in the SAN which has changed hardware paths. We overcame this by running 'vgscan -a' to remove the orignal alternate paths and replace them with the new paths. This has worked well on all our servers except one. When running 'insf -e' to install the special device files for the new paths, the 'insf -e' just runs up until the stape devices and hangs. We are unable to kill the process. If we run an ioscan after the insf command, it hangs too and cannot kill it. (but it runs fine prior to the insf) The ioscan does not display any output up to when hanging.
We have no stape devices attached to this server and I have used rmsf to delete all stape devices under /dev.
Still insf hangs during the stapes. I have also tried 'inst -C disk' to just try load the special devices for the disks without hitting the stape devices, but the command ends without having created any files.
Assistance would be appreciated.
We have no stape devices attached to this server and I have used rmsf to delete all stape devices under /dev.
Still insf hangs during the stapes. I have also tried 'inst -C disk' to just try load the special devices for the disks without hitting the stape devices, but the command ends without having created any files.
Assistance would be appreciated.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-12-2009 05:53 PM
09-12-2009 05:53 PM
Re: insf -e hangs (HP-UX 11.11i v1)
Hi
Seen this before and also with tape devices. Verify connectivity or lack of connectivity to your tape devices.
cstm<<-EOF
runutil logtool
rs
EOF
Should specifically name the problem device. It will have the highest integer number.
Seen this before and also with tape devices. Verify connectivity or lack of connectivity to your tape devices.
cstm<<-EOF
runutil logtool
rs
EOF
Should specifically name the problem device. It will have the highest integer number.
Support Fatherhood - Stop Family Law
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP