rx6600 Linux HBA problem

[skt_skt]

i meant you need to rebuild the *.img(take a backup) after the chnages in modprobe.conf.

[MartyB]

Unfortunately, it's still a no go. Here's a snip from /var/log/messages on this most recent reboot:

Mar 20 18:06:27 host kernel: mptbase: Initiating ioc0 bringup
Mar 20 18:06:27 host kernel: ioc0: SAS1068: Capabilities={Initiator}
Mar 20 18:06:27 host kernel: scsi1 : ioc0: LSISAS1068, FwRev=01100000h, Ports=1, MaxQ=268, IRQ=54
Mar 20 18:06:27 host kernel: Vendor: HP Model: DG072ABAB3 Rev: HPD5
Mar 20 18:06:27 host kernel: Type: Direct-Access ANSI SCSI revision: 05
Mar 20 18:06:27 host kernel: SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB)
Mar 20 18:06:27 host kernel: SCSI device sda: drive cache: write through
Mar 20 18:06:27 host kernel: SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB)
Mar 20 18:06:27 host kernel: SCSI device sda: drive cache: write through
Mar 20 18:06:27 host kernel: sda: sda1 sda2 sda3
Mar 20 18:06:27 host kernel: Attached scsi disk sda at scsi1, channel 0, id 3, lun 0
Mar 20 18:06:27 host kernel: Vendor: HP Model: DG072ABAB3 Rev: HPD5
Mar 20 18:06:27 host kernel: Type: Direct-Access ANSI SCSI revision: 05
Mar 20 18:06:27 host kernel: SCSI device sdb: 143374738 512-byte hdwr sectors (73408 MB)
Mar 20 18:06:27 host kernel: SCSI device sdb: drive cache: write through
Mar 20 18:06:27 host kernel: SCSI device sdb: 143374738 512-byte hdwr sectors (73408 MB)
Mar 20 18:06:27 host kernel: SCSI device sdb: drive cache: write through
Mar 20 18:06:27 host kernel: sdb: sdb1 sdb2
Mar 20 18:06:27 host kernel: Attached scsi disk sdb at scsi1, channel 0, id 4, lun 0
Mar 20 18:06:27 host kernel: ACPI: PCI Interrupt 0000:0f:01.0[A] -> GSI 49 (level, low) -> IRQ 53
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Found an ISP2422, irq 53, iobase 0xc0000000b0040000
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Configuring PCI space...
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Configure NVRAM parameters...
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Verifying loaded RISC code...
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Allocated (64 KB) for EFT...
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Allocated (1413 KB) for firmware dump...
Mar 20 18:06:27 host kernel: qla2400 0000:0f:01.0: Waiting for LIP to complete...
Mar 20 18:06:28 host kernel: qla2400 0000:0f:01.0: LIP reset occured (f7f7).
Mar 20 18:06:28 host kernel: qla2400 0000:0f:01.0: LOOP UP detected (2 Gbps).
Mar 20 18:06:28 host kernel: qla2400 0000:0f:01.0: Topology - (F_Port), Host Loop address 0x0
Mar 20 18:06:28 host kernel: scsi2 : qla2xxx
Mar 20 18:06:28 host kernel: qla2400 0000:0f:01.0:
Mar 20 18:06:28 host kernel: QLogic Fibre Channel HBA Driver: 8.01.07.15
Mar 20 18:06:28 host kernel: QLogic HP AB378-60101 -
Mar 20 18:06:28 host kernel: ISP2422: PCI-X Mode 2 (133 MHz) @ 0000:0f:01.0 hdma+, host#=2, fw=4.00.26 [IP]
Mar 20 18:06:28 host kernel: scsi: unknown device type 12
Mar 20 18:06:28 host kernel: Vendor: EMC Model: SYMMETRIX Rev: 5771
Mar 20 18:06:28 host kernel: Type: RAID ANSI SCSI revision: 02
Mar 20 18:06:28 host kernel: qla2400 0000:0f:01.0: scsi(2:0:0:0): Enabled tagged queuing, queue depth 32.
Mar 20 18:06:28 host kernel: ACPI: PCI Interrupt 0000:23:01.0[A] -> GSI 93 (level, low) -> IRQ 57
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Found an ISP2422, irq 57, iobase 0xc0000000f0040000
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Configuring PCI space...
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Configure NVRAM parameters...
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Verifying loaded RISC code...
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Allocated (64 KB) for EFT...
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Allocated (1413 KB) for firmware dump...
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Waiting for LIP to complete...
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: LIP reset occured (f7f7).
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: LOOP UP detected (2 Gbps).
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: Topology - (F_Port), Host Loop address 0x0
Mar 20 18:06:28 host kernel: scsi3 : qla2xxx
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0:
Mar 20 18:06:28 host kernel: QLogic Fibre Channel HBA Driver: 8.01.07.15
Mar 20 18:06:28 host kernel: QLogic HP AB378-60101 -
Mar 20 18:06:28 host kernel: ISP2422: PCI-X Mode 2 (133 MHz) @ 0000:23:01.0 hdma+, host#=3, fw=4.00.26 [IP]
Mar 20 18:06:28 host kernel: scsi: unknown device type 12
Mar 20 18:06:28 host kernel: Vendor: EMC Model: SYMMETRIX Rev: 5771
Mar 20 18:06:28 host kernel: Type: RAID ANSI SCSI revision: 02
Mar 20 18:06:28 host kernel: qla2400 0000:23:01.0: scsi(3:0:0:0): Enabled tagged queuing, queue depth 32.
Mar 20 18:06:28 host kernel: device-mapper: 4.5.5-ioctl (2006-12-01) initialised: dm-devel@redhat.com

Does anything jump out?

Thanks for the help!

[skt_skt]

Do you power path also here? If not ignore.
PP and DM need to be present at the same time.

[MartyB]

Nope, no PowerPath installed on this system.

[MartyB]

FINALLY! After getting our SAN guy to take another look, there was some zoning issue that he overlooked. It's all good now.

Thanks so much for everyone's advice.

[MartyB]

see last comment

[skt_skt]

let us know what was really wrong at SAN side?

masking Databse not refreshed or what ever...