rx7640 unable to install OS

[SHADRACH AMARH]

heloo guys
i mistakenly deleted my /dev file and i try doing a new instalation but when the hp-ux cd is booting,it get to a stage and stops after some hrs, it gives an error....logs are bellow.. can someone please help me ?




EFI version 1.10 [14.61] Running on GenuineIntel Itanium(R) 2 Processor
EFI server rx7640 SAL [15:36:49] - HP
Loading 'BRM5701_LAN'...

Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.11

driver: Image BRM5701_LAN loaded at 40FFC46000-40FFC80000. Returned Success
Loading 'FPSWA'...
driver: Image FPSWA loaded at 40FFBDA000-40FFC44000. Returned Success
PciRom S=01 B=00 D=3 F=0 I=0 loaded at 40FFB72000-40FFBD8000
Scsi(Pun2,Lun0) Optiarc DVD RW AD-5170A 1.32 ( 40 MBytes/sec)
PciRom S=01 B=1D D=4 F=0 I=0 loaded at 40FFB0C000-40FFB72000
PciRom S=01 B=1D D=6 F=0 I=0 loaded at 40FFAC4000-40FFB0C000
PciRom S=01 B=39 D=4 F=0 I=0 loaded at 40FFA9B000-40FFAC2000
PciRom S=01 B=39 D=6 F=0 I=0 loaded at 40FFA60000-40FFA9A000

Copyright (c) 2000-2005 Broadcom Corporation
Broadcom NetXtreme Gigabit Ethernet EFI driver v7.0.11

HPPress to run the Option ROM Configuration for Arrays Utility
BrPress to skip configuration and continue
PciRom S=01 B=C7 D=4 F=0 I=1 loaded at 40FFA0C000-40FFA60000
HP Smart Array 6400-128 Controller (version 2.84) 1 Logical Drive
1794-Drive Array - Array Accelerator Battery Charge Low
Array Accelerator Posted-Write Cache is temporarily disabled.
Array Accelerator will be reenabled when batteries reach full charge.
1778-Drive Array resuming Automatic Data Recovery process









* Installing bundle "scsiU320-00,r=B.11.23.0712" .
NOTE: Creating the initial "/stand/system" file using the
"/usr/lbin/sysadm/create_sysfile" command.
* Installing fileset "BLKONLY-MS.BLKONLY-MS-KRN,r=C.01.04.07" (1
of 1924).
* Installing fileset "BOOT-KBD.BOOT-KBD-KRN,r=C.01.04.07" (2 of
1924).
* Installing fileset "BOOT-MOUSE.BOOT-MOUSE-KRN,r=C.01.04.07" (3
of 1924).
* Installing fileset "DCE-Core.DCE-CORE-SHLIB,r=B.11.23" (4 of
1924).
* Installing fileset "OS-Core.C-KRN,r=B.11.23" (5 of 1924).


DIAGNOSTIC SYSTEM WARNING:
The diagnostic logging facility has started receiving excessive
errors from the I/O subsystem. I/O error entries will be lost
until the cause of the excessive I/O logging is corrected.
If the diaglogd daemon is not active, use the Daemon Startup command
in stm to start it.
If the diaglogd daemon is active, use the logtool utility in stm
to determine which I/O subsystem is logging excessive errors.

[Steven E. Protter]

Shalom,

Looks like your drive controller has a weak battery.

HP Smart Array 6400-128 Controller (version 2.84) 1 Logical Drive
1794-Drive Array - Array Accelerator Battery Charge Low

Get that resolved and the OS install will probably go better.

SEP

[SHADRACH AMARH]

yeah..
i changed the cache battery it was giving the same error, i also changed the whole controller including the battery and it was giving the same error so what do u think will be the course ????

[AnthonySN]

>>* Installing fileset "OS-Core.C-KRN,r=B.11.23" (5 of 1924).


it is not able to read the dvd beyond that point.

change the dvd.

[Adisuria Wangsadinata_1]

Hi Amarh,

Good day to you !
To isolated the issue comes from your DVD or from the peripheral that attached to your system, please try to set your system to minimum requirement by disconnected all peripheral first (eg. external disk, FC connection).

Once the OS installed to your system, you can connect those peripheral that has been disconnected back to your system.

This method also will speed up the installation process, since the system didn't have to scan all the connected devices.

Hope this information can help.

Regards,
Adi.