Operating System - HP-UX
1748266 Members
3608 Online
108760 Solutions
New Discussion юеВ

sautil & BUS RESET RECOVERY ABORTED

 
SOLVED
Go to solution
Ludovic Derlyn
Esteemed Contributor

sautil & BUS RESET RECOVERY ABORTED

hi

this is the result of my sautil
vgchange -a y -q n /dev/vgXx not working


******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.06 ****
**** ****
**** (C) Copyright 2003, 2004 Hewlett-Packard Development Company, L.P. ****
******************************************************************************



---- DRIVER INFORMATION ------------------------------------------------------

Driver State........................ READY

---- CONTROLLER INFORMATION --------------------------------------------------

Controller Product Number........... A9890A
Controller Product Name............. HP PCI-X SmartArray 6402
Hardware Path....................... 0/4/1/0/4/0
Serial Number....................... P57820PXQR80R0
Device File......................... /dev/ciss5
Hardware Revision................... 'B'
Boot Block Revision................. 3.86
Firmware Revision (running)......... 2.34
Firmware Revision (in ROM).......... 2.34
Firmware Revision (inactive)........ 2.34
# of Logical Drives................. 3
# of Physical Disks Configured...... 14
# of Physical Disks Detected........ 14
Logical Drive Rebuild Priority...... 118 (high)
Array Capacity Expansion Priority... 0 (low)
Auto-Fail Missing Disks at Boot..... enabled
SCSI Transfer Detection Mode........ Auto Detect


---- ARRAY ACCELERATOR (CACHE) INFORMATION -----------------------------------

Array Accelerator Board Present?.... yes
Cache Configuration Status.......... cache enabled
Cache Ratio......................... 50% Read / 50% Write
Total Cache Size (MB)............... 128
Read Cache........................ 064
Write Cache....................... 064
Transfer Buffer................... 000
Battery Pack Count.................. 2
Battery Status (pack #1)............ ok
Battery Status (pack #2)............ ok


---- LOGICAL DRIVE SUMMARY ---------------------------------------------------

# RAID Size Status

0 5 277841 MB FAILED
1 5 277841 MB FAILED
2 5 208380 MB FAILED


---- SCSI DEVICE SUMMARY -----------------------------------------------------

Location Ch ID Type Capacity Status

external 1 0 DISK 72.8 GB OK
external 1 1 DISK 72.8 GB OK
external 1 2 DISK 72.8 GB OK
external 1 3 DISK 72.8 GB OK
external 1 4 DISK 72.8 GB OK
external 1 5 DISK 72.8 GB OK
external 1 7 PROCESSOR
external 1 8 DISK 72.8 GB OK
external 1 9 DISK 72.8 GB OK
external 1 10 DISK 72.8 GB OK
external 1 11 DISK 72.8 GB OK
external 1 12 DISK 72.8 GB OK
external 1 13 DISK 72.8 GB OK
external 1 14 DISK 72.8 GB OK
external 1 15 DISK 72.8 GB OK


---- SCSI BUS SUMMARY --------------------------------------------------------

External Internal
Ch LVD_Mode Connector Connector

1 YES YES -
2 YES - -


---- LOGICAL DRIVE 0 ---------------------------------------------------------

Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding)
Logical Drive Size.................. 277841 MB
Logical Drive Status................ FAILED
# of Participating Physical Disks... 5

Participating Physical Disk(s)...... Ch:ID
1: 0
1: 1
1: 2
1: 3
1: 4

Participating Spare Disk(s)......... Ch:ID
none

Stripe Size......................... 16 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0x0
Media Exchange Detected?............ yes


---- LOGICAL DRIVE 1 ---------------------------------------------------------

Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding)
Logical Drive Size.................. 277841 MB
Logical Drive Status................ FAILED
# of Participating Physical Disks... 5

Participating Physical Disk(s)...... Ch:ID
1: 5
1: 8
1: 9
1:10
1:11

Participating Spare Disk(s)......... Ch:ID
none

Stripe Size......................... 16 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0x0
Media Exchange Detected?............ yes


---- LOGICAL DRIVE 2 ---------------------------------------------------------

Fault Tolerance Mode................ RAID 5 (Distributed Data Guarding)
Logical Drive Size.................. 208380 MB
Logical Drive Status................ FAILED
# of Participating Physical Disks... 4

Participating Physical Disk(s)...... Ch:ID
1:12
1:13
1:14
1:15

Participating Spare Disk(s)......... Ch:ID
none

Stripe Size......................... 16 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0x0
Media Exchange Detected?............ yes


---- SCSI DEVICE 1:0 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 0
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07287B55
Device Serial Number............................. E40AY0SK
Device Firmware Version.......................... HPB2
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:1 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 1
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07287B55
Device Serial Number............................. E40B8J4K
Device Firmware Version.......................... HPB2
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:2 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 2
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07287B55
Device Serial Number............................. E40AB61K
Device Firmware Version.......................... HPB2
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:3 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 3
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07287B55
Device Serial Number............................. E40B9NCK
Device Firmware Version.......................... HPB2
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:4 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 4
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07287B55
Device Serial Number............................. E40AB8GK
Device Firmware Version.......................... HPB2
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:5 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 5
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07288285
Device Serial Number............................. 3KP163ZD00007608T3JW
Device Firmware Version.......................... HPB3
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:7 [PROCESSOR] ---------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 7
Device Type...................................... PROCESSOR
Device Vendor ID................................. COMPAQ
Device Product ID................................ PROLIANT 4LEE
SCSI Transfer Rate (maximum)..................... Ultra-320


---- SCSI DEVICE 1:8 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 8
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF0728A4CB
Device Serial Number............................. 3KP1Y8D400007621HBA5
Device Firmware Version.......................... HPB5
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:9 [DISK] --------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 9
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF0728A4CB
Device Serial Number............................. 3KP1X02Q00007620YERD
Device Firmware Version.......................... HPB5
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:10 [DISK] -------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 10
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF0728A4CB
Device Serial Number............................. 3KP1V5T500007621YDT7
Device Firmware Version.......................... HPB5
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:11 [DISK] -------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 11
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF072863BA
Device Serial Number............................. C80508CK
Device Firmware Version.......................... HPB4
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ no
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:12 [DISK] -------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 12
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF0728A4CB
Device Serial Number............................. 3KP1YBRL00007621GAUL
Device Firmware Version.......................... HPB5
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ no
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:13 [DISK] -------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 13
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07288285
Device Serial Number............................. 3KP1E2GY00007610NE02
Device Firmware Version.......................... HPB5
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ no
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:14 [DISK] -------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 14
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07288576
Device Serial Number............................. ANA1P5A07L9B0540
Device Firmware Version.......................... HPB2
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ no
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- SCSI DEVICE 1:15 [DISK] -------------------------------------------------

Connector Location............................... external
Channel Number................................... 1
SCSI ID.......................................... 15
Device Type...................................... DISK
Disk Capacity.................................... 72.8 GB
Device Status.................................... OK
Device Vendor ID................................. COMPAQ
Device Product ID................................ BF07288285
Device Serial Number............................. 3KP1F7B700007610GXE7
Device Firmware Version.......................... HPB5
SCSI Transfer Rate (actual)...................... Ultra-320
Reserved Area (cfg/status info).................. 557.1 KB (0.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ no
Last Failure Reason.............................. BUS RESET RECOVERY ABORTED

Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Wide SCSI transfer enabled..................... yes
Synchronous (Fast/Ultra) transfer enabled...... yes
Narrow disk tray detected...................... no
Wide transfer failed, reverted to narrow....... no
Ultra SCSI transfer enabled.................... yes
Ultra-2 SCSI transfer enabled.................. yes

S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external channel................... yes
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no

Running in DT clocking mode.................... yes
Supports DT clocking mode only................. no
Supports DT and ST clocking modes.............. yes
Running in U320 mode........................... yes
Packetized SCSI supported...................... yes
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes

QAS capable (U320 only)........................ yes
Currently running QAS (U320 only).............. yes



---- DIAGRAM OF EXTERNAL CONNECTORS ON BRACKET -------------------------------

========---========
| |
| U320 <--- LOOK FOR THIS LOGO
| / \ |
| <- |
| \ / |
| |
| * * |
| * * * * |
(Ch A1)---> * * * * <--- (Ch A2)
| * * * * |
| * * |
| |
| |
| |
| |
| |
| |
| |
| |
| |
~ ~ ~ ~ ~


******************************************************************************
**** End of SAUTIL Output ****
******************************************************************************

this problem will be resolving by sautil /dev/ciss5 start_recovery ?

thanks
2 REPLIES 2
rariasn
Honored Contributor
Solution

Re: sautil & BUS RESET RECOVERY ABORTED

Hi,

Q: What does the auto-fail missing disks at boot option control?
A: The auto-fail missing disks at boot option controls the power-on behavior of the
HP-UX RAID controller when some of the configured drives are missing. Auto-fail is enabled when the first logical drive is created by the saconfig utility. You can then disable it with the saconfig -F command.

As an example, consider the following scenario:

1. The boot volume is on a RAID logical drive.

2. The system is powered off.

3. The cable for an enclosure containing configured disks is accidentally disconnected from the controller.

4. All disks belonging to the boot volume are still connected to the controller.
5. The system is then powered on.

If auto-fail is enabled in this scenario: During POST, the controller fails the missing disks.

Non-fault-tolerant logical drives are FAILED. Fault-tolerant logical drives either transition to Interim Recovery (degraded) mode or to FAILED depending on the number of disks the logical drive is missing. The system then begins booting HP-UX.
During boot, the ciss init script detects the degraded/failed logical drives and generates an error that instructs you to run sautil. The sautil utility displays the degraded/failed logical drives and failed disks. At this point, you can either power off the system, reconnect the disks, and boot again; or reconnect the disks and run the sautil accept media exchange command
to change the disks and logical drives back to OK state. For more information, see ├в The sautil accept_media_xchg Command├в (page 63).
If auto-fail is disabled in the previous scenario:[HP/9000 system] The controller temporarily disables all logical drives, including the intact boot volume. The system fails to boot.
[HP Integrity system] During POST, you can choose one of the following options:
1. Power off the system and reconnect the disks.
2. Press F1. The controller temporarily disables all logical drives, including the intact boot volume. The system fails to boot.
3. Press F2. The system takes the same actions as system with auto-fail enabled, as previously described

http://docs.hp.com/en/J6369-90051/J6369-90051.pdf

rgs
Ludovic Derlyn
Esteemed Contributor

Re: sautil & BUS RESET RECOVERY ABORTED

excellent
thanks !