Operating System - Tru64 Unix
1753265 Members
5121 Online
108792 Solutions
New Discussion юеВ

Re: unable to boot the tru64 unix server from the SRM prompt

 
Rob Leadbeater
Honored Contributor

Re: unable to boot the tru64 unix server from the SRM prompt

Hi,

Can you post as much detail about the hardware as you can please... The output of "show dev" from the P00>>> prompt would be useful.

Going through the previous posts, I suspect that you are not booting from the correct disk. If you have got a SWXCR card, then I'll guess that your boot device should be a DR* device rather than DK*.

The output of "show boot*" would also help.

Cheers,

Rob
Vladimir Fabecic
Honored Contributor

Re: unable to boot the tru64 unix server from the SRM prompt

And output of:
>>> show *
would also help
In vino veritas, in VMS cluster
sk.imran
Advisor

Re: unable to boot the tru64 unix server from the SRM prompt

Dear Vladimir Fabecic,

Thanks for the reply.

As i concerned no one plays with the server after it goes down.

And today we got the right media V5.1

and df command shows the cd partition and the new / partition nothiong esle.

As we have sysbackup...

please give the steps to perform the restoration and how to install it.
hp ux csa
Vladimir Fabecic
Honored Contributor

Re: unable to boot the tru64 unix server from the SRM prompt

Before that, please sent output of:
>>> show device
>>> show config
to have more information about your hardware.
In vino veritas, in VMS cluster
sk.imran
Advisor

Re: unable to boot the tru64 unix server from the SRM prompt

Hello,

Please find the sh dev and sh config command output.

P00>>>sh dev
dkd0.0.9.0 DKD0 RZ2DA-LA N1H1
dkd100.1.0.9.0 DKD100 COMPAQ BD0366349C 3B06
dkd200.2.0.9.0 DKD200 COMPAQ BD0366349C 3B06
dkd300.3.0.9.0 DKD300 COMPAQ BD0366349C 3B06
dkd400.4.0.9.0 DKD400 COMPAQ BD0366349C 3B06
dkd500.5.0.9.0 DKD500 COMPAQ BD0366349C 3B06
dkd600.6.0.9.0 DKD600 RZ1DB-CA LYJ0
dqa0.0.0.105.0 DQA0 CD-224E 9.5B
dra0.0.0.7.1 DRA0 2 Member RAID 1
dva0.0.0.0.0 DVA0
jba601.6.0.8.1 JKA601 BECHMARK VS640 5032
jba600.6.0.8.1 JKA600 BECHMARK VS640 5032
eia0.0.0.9.1 EIA0 00-50-8B-6D-FB-76
pka0.7.0.8.1 PKA0 SCIS BUS ID 7 5.57
pkb0.7.0.6.1 PKB0 SCIS BUS ID 7
pkc0.7.0.106.1 PKC0 SCIS BUS ID 7
pkd0.7.0.9.1 PKD0 SCIS BUS ID 7 5.57



P00>>>sh config

the out out is so log but I am giving u the some details:

P00>>>sh config

SRM Console: V5.8-10

Bus 00 Slot 09:Qlogic ISP10x0
pkd0.7.0.9.1 SCSI Bus ID 7
dkd0.0.0.9.0 RZ2DA-LA
dkd100.1.0.9.0 COMPAQ BD0366349C
dkd200.2.0.9.0 COMPAQ BD0366349C
dkd300.3.0.9.0 COMPAQ BD0366349C
dkd400.4.0.9.0 COMPAQ BD0366349C
dkd500.5.0.9.0 COMPAQ BD0366349C
dkd600.6.0.9.0 RZ1DB-CA



waiting for ur reply!!!
hp ux csa
Vladimir Fabecic
Honored Contributor

Re: unable to boot the tru64 unix server from the SRM prompt

So you have 7 disks connected to "normal" SCSI controller and 2 disk connected to SWXCR.
Now I am a little bit confused.
Please boot from install CD and send output of:
# hwmgr -view device
It is very important to see which disk is mapped as dsk0
I will have not much time today so please hurry.
In vino veritas, in VMS cluster
Vladimir Fabecic
Honored Contributor

Re: unable to boot the tru64 unix server from the SRM prompt

And please send output of:
# disklabel -r dsk1
In vino veritas, in VMS cluster
Vladimir Fabecic
Honored Contributor

Re: unable to boot the tru64 unix server from the SRM prompt

Looks like your "old root" should be dsk1a not dsk0a. Waiting for your reply.
Procedure:
1.
# cd /etc/fdmns
# mkdir tmproot
# cd tmproot
# ln -s /dev/disk/dsk1a
# cd /
# mount tmproot#root /mnt
Send output of:
# ls -al /mnt
2.
# dn_setup -install_tape
Send output of:
# hwmgr -show scsi
3.
Restoring file system backup tape
(lets say that "old root" is already mounted in /mnt)
# cd /mnt
# vrestore -x -f /dev/ntape/tape0 (or whatever is tape device)

But you must be sure you have the right save set loaded in tape drive.
To check out do:
# vrestore -i -f /dev/ntape/tape0
and do "ls" when get prompt
In vino veritas, in VMS cluster
sk.imran
Advisor

Re: unable to boot the tru64 unix server from the SRM prompt

Hi,

please find the the output of hwmgr -view device

qvces40#hwmgr -view device
HWID: Device Name Mfg Model Location
------------------------------------------------------------------------------

4: (unknown)
13: /dev/cport/scp0 SWXCR xcr0
14: /dev/disk/floppy0c 3.5in floppy fdi0-unit-0
43: /dev/disk/dsk0c SWXCR ctlr-0-unit-0
56: /dev/disk/cdrom0c COMPAQ CRD-224E bus-1-targ-0-lun-0
57: /dev/disk/dsk1c DEC RZ2DA-LA bus-5-targ-0-lun-0
58: /dev/disk/dsk2c COMPAQ BD0366349C bus-5-targ-1-lun-0
59: /dev/disk/dsk3c COMPAQ BD0366349C bus-5-targ-2-lun-0
60: /dev/disk/dsk4c COMPAQ BD0366349C bus-5-targ-3-lun-0
61: /dev/disk/dsk5c COMPAQ BD0366349C bus-5-targ-4-lun-0
62: /dev/disk/dsk6c COMPAQ BD0366349C bus-5-targ-5-lun-0
63: /dev/disk/dsk7c DEC RZ1DB-CA bus-5-targ-6-lun-0
64: (unknown) VS640 bus-0-targ-6-lun-0

hp ux csa
sk.imran
Advisor

Re: unable to boot the tru64 unix server from the SRM prompt

Hello,

#hwmgr -view device
HWID: Device Name Mfg Model Location
------------------------------------------------------------------------------

4: (unknown)
13: /dev/cport/scp0 SWXCR xcr0
14: /dev/disk/floppy0c 3.5in floppy fdi0-unit-0
43: /dev/disk/dsk0c SWXCR ctlr-0-unit-0
56: /dev/disk/cdrom0c COMPAQ CRD-224E bus-1-targ-0-lun-0
57: /dev/disk/dsk1c DEC RZ2DA-LA bus-5-targ-0-lun-0
58: /dev/disk/dsk2c COMPAQ BD0366349C bus-5-targ-1-lun-0
59: /dev/disk/dsk3c COMPAQ BD0366349C bus-5-targ-2-lun-0
60: /dev/disk/dsk4c COMPAQ BD0366349C bus-5-targ-3-lun-0
61: /dev/disk/dsk5c COMPAQ BD0366349C bus-5-targ-4-lun-0
62: /dev/disk/dsk6c COMPAQ BD0366349C bus-5-targ-5-lun-0
63: /dev/disk/dsk7c DEC RZ1DB-CA bus-5-targ-6-lun-0
64: (unknown) VS640 bus-0-targ-6-lun-0

hp ux csa