- Community Home
- >
- Servers and Operating Systems
- >
- Operating Systems
- >
- Operating System - OpenVMS
- >
- ECP analyze display error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-28-2011 04:20 AM
09-28-2011 04:20 AM
Hi
I have installed TDC 2.3-20 on VMS 8.4 and tried to analyze performance, but I get an error.
GRIPEN> plan analyze/motif
Enterprise Capacity Performance Analyzer (c) 1997, 2006 Hewlett-Packard Develop ment Company, L.P., All Rights Reserved.
gripen$dka0:[sys0.syscommon.][sysexe]ecp$analyze_motif.exe;1: Can't open display
GRIPEN> mc decw$puzzle . ! Works ok.
I also directed the output to my PC:
SET DISPLAY/CREATE/TRANSPORT=TCPIP/NODE=axdt0608.samba.net gave the same error and decw$puzzle works.
Tried the following with the same result:
SET DISPLAY/CREATE/NODE=GRIPEN/TRANSPORT=DECNET
SET DISPLAY/CREATE/NODE=GRIPEN/TRANSPORT=TCPIP
SET DISPLAY/CREATE/NODE=GRIPEN/TRANSPORT=LOCAL
Availibility Manager command avail/analyze works with the display on my PC.
It can also start a display on my workstation but that only starts an all grey window with no lines or columns in it.
But that is another problem.
Any clue?
Regard Jan Andersson
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-28-2011 06:10 PM
09-28-2011 06:10 PM
Re: ECP analyze display error
Jan,
Very odd! I get a display from OpenVMS/Alpha V8.4 running ECP$ANALYZE_MOTIF version:
image name: "DI_MOTIF"
image file identification: "ECP V5.6A-30"
image file build identification: ""
link date/time: 23-MAY-2006 13:48:07.51
linker identification: "A13-03"
with the display using /TRANSPORT=TCPIP pointing to a PC running ReflectionX
If your display is the local node, you should be using SET DISPLAY/TRANSPORT=LOCAL/NODE=YOURNODE.
Maybe there's a quota issue which is preventing the display from opening? My quotas for a subprocess running ECP$ANALYZE_MOTIF look like this (SHOW PROCESS/CONTINUOUS/ID=pid then hit Q):
# open files remaining 97/100 ( 97%) Direct I/O count/limit 150/150 (100%) Buffered I/O count/limit 149/150 ( 99%) BUFIO byte count/limit 296544/296672 ( 99%) ASTs remaining 995/1000 ( 99%) Timer entries remaining 199/200 ( 99%) PGFL quota count/limit 29929/31250 ( 95%) ENQ quota count/limit 4996/5000 ( 99%)
Nothing spectacular, but maybe worth checking.
Unfortunately the secondary error, which would tell you WHY the display can't be opened has been omitted by the programmer. A long shot, check $STATUS immediately after the failed command, maybe that has more information?
Please log a case with your local customer support centre, as well as assisting you, they should send feedback to engineering to fix their error reporting!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
09-30-2011 04:16 AM
09-30-2011 04:16 AM
Re: ECP analyze display error
As my ds10 workstation has became a bit messed up, I did a clean VMS install of 8.4.
Trying to install ECP fails.
Beginning installation of VECP0 V56.A at 12:53
%VMSINSTAL-E-EXPIRED, This product has expired after OpenVMS Alpha version 8.3 %VMSINSTAL-E-EXPIRED, Please contact your local hp sales representative %VECP0-E-UNSUPVMSVER, Installation of this kit on this version of OpenVMS is not supported.
%VMSINSTAL-E-INSFAIL, The installation of VECP0 V56.A has failed.
Earlier I had ECP installed before the upgrade to VMS 8.4.
Maybe it just don't run on VMS 8.4 even thogh it is an Alpha.
I know it's not for Itanium but theres nothing said about Alpha.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-06-2011 02:37 AM - edited 10-06-2011 02:45 AM
10-06-2011 02:37 AM - edited 10-06-2011 02:45 AM
SolutionJan,
do you have to happen a symbol named DISPLAY defined in your process ? That would be one possible cause for the problem you're describing. For some reason, the DECwindows routines seem to try a symbol with that name when creating the display.
Volker.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-13-2011 04:29 AM
10-13-2011 04:29 AM
Re: ECP analyze display error
Now it's working!!
Thanks a lot Volker.
Now I just have to install it on VMS 8.3 and then upgrade to 8.4 to see if it still works.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
01-11-2012 03:24 PM
01-11-2012 03:24 PM
Re: ECP analyze display error
To identify a network problem, rather than an ECP problem, run an ecp comand line
plan analyze/beg=/end=/node=nodename
I use the ported ECP