- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- A very strange problem
StoreEver Tape Storage
1752650
Members
5574
Online
108788
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-10-2004 01:25 AM
06-10-2004 01:25 AM
A very strange problem
Hi all,
I would like your attention on problem that affecting my SAN from 2 months about. Every Monday I eject a tape from my MSL5000 library with DataProtector 5.10 and all it's ok, but when I push "Mail Slot Access" and open Ultrium door to get a tape in a mailslot 0 all the SAN is blocked and cell manager has many errors reported in system event viewer about fibre channel card timeout. During the problem all the drive couldn't be found or the time to discovery them is very too...... (devbra -dev work but it is very slow, about 5 minutes...)
Could something hel me?
Thank in advance,
Salvatore.
I would like your attention on problem that affecting my SAN from 2 months about. Every Monday I eject a tape from my MSL5000 library with DataProtector 5.10 and all it's ok, but when I push "Mail Slot Access" and open Ultrium door to get a tape in a mailslot 0 all the SAN is blocked and cell manager has many errors reported in system event viewer about fibre channel card timeout. During the problem all the drive couldn't be found or the time to discovery them is very too...... (devbra -dev work but it is very slow, about 5 minutes...)
Could something hel me?
Thank in advance,
Salvatore.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-13-2004 10:39 PM
06-13-2004 10:39 PM
Re: A very strange problem
When you push "mail slot access" is the front led blinking (triangle)? If it is so
the library changes to the offline mode. When there is an active backup or any other communication established between server and storage at this moment you will get error messages.
the library changes to the offline mode. When there is an active backup or any other communication established between server and storage at this moment you will get error messages.
Christian
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP