- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- BAD Media
StoreEver Tape Storage
1752786
Members
5669
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-12-2006 03:49 PM
тАО06-12-2006 03:49 PM
BAD Media
1)I have run the omnimm -reset_poor_media on the poor media in the data protector.
But still it is showing in "Poor" flag only.
OR VErify will destory any data from the tape.
2) After formatting the Media is there anything we need to do to initial the tape or we can directly start the backup
pls advice
But still it is showing in "Poor" flag only.
OR VErify will destory any data from the tape.
2) After formatting the Media is there anything we need to do to initial the tape or we can directly start the backup
pls advice
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-12-2006 11:26 PM
тАО06-12-2006 11:26 PM
Re: BAD Media
Ravikant,
1) If the tape is still showing that it is poor after the reset poor media, then it could be that your tape needs replacing. Try to format the tape, thus deleting it. If it still says poor after a full format, then bin it!
2) After formatting the media, there is no need to do anything else to it, you can then set off your backup, when required. Make sure you put it in the right pool for your backups.
Hope that helps.
JASH
1) If the tape is still showing that it is poor after the reset poor media, then it could be that your tape needs replacing. Try to format the tape, thus deleting it. If it still says poor after a full format, then bin it!
2) After formatting the media, there is no need to do anything else to it, you can then set off your backup, when required. Make sure you put it in the right pool for your backups.
Hope that helps.
JASH
If I can, I will!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-13-2006 12:42 PM
тАО06-13-2006 12:42 PM
Re: BAD Media
Thanks JASH ....
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP