- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Connecting a MSL 6060 directly to server
StoreEver Tape Storage
1753312
Members
5675
Online
108792
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2009 11:02 AM
тАО01-22-2009 11:02 AM
Connecting a MSL 6060 directly to server
Hello Guys.
I have a ttached an HP MSL 6060 Library directly to an rp2470 Server(O.S. 11.11) via fiber channel.
But I am unable to see the library, Can you offer any leads as to what I must configure, I already tryed different fiber channel cards, different cables, etc.
Note: This library was connected to a SAN environment, but not anymore.
I have a ttached an HP MSL 6060 Library directly to an rp2470 Server(O.S. 11.11) via fiber channel.
But I am unable to see the library, Can you offer any leads as to what I must configure, I already tryed different fiber channel cards, different cables, etc.
Note: This library was connected to a SAN environment, but not anymore.
Knowledge is power.
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2009 11:21 AM
тАО01-22-2009 11:21 AM
Re: Connecting a MSL 6060 directly to server
hi
make sure that u have the modules schgr and stape configured in the kernel
u can use sam to see the module section in the Kernel configuration.
also seee that u are having the Fiber channel drivers in the system properly installed.
#ioscan -fnCfc
this will show device files as /dev/td0 or /dev/fcd0
then do
#fcmsutil /dev/td0
or
#fcmsutil /dev/fcd0
depending on u have /dev/td0 or /dev/fcd0 or the fiber card connected is /dev/td1 or /dev/fcd1 to which the Tape drive is connected properly.
in the fcmsutil O/P u shud see that Port WWN and Node WWN no is there and that u can see online if the FC card is conn to the Tape Library and Library is powered on and initialised.
try postingg the O/Ps of the following commands.
Also suggested that ur system has the latest HWEnable Bundle patches installed.
#swlist -l bundle
Regards
Sujit
make sure that u have the modules schgr and stape configured in the kernel
u can use sam to see the module section in the Kernel configuration.
also seee that u are having the Fiber channel drivers in the system properly installed.
#ioscan -fnCfc
this will show device files as /dev/td0 or /dev/fcd0
then do
#fcmsutil /dev/td0
or
#fcmsutil /dev/fcd0
depending on u have /dev/td0 or /dev/fcd0 or the fiber card connected is /dev/td1 or /dev/fcd1 to which the Tape drive is connected properly.
in the fcmsutil O/P u shud see that Port WWN and Node WWN no is there and that u can see online if the FC card is conn to the Tape Library and Library is powered on and initialised.
try postingg the O/Ps of the following commands.
Also suggested that ur system has the latest HWEnable Bundle patches installed.
#swlist -l bundle
Regards
Sujit
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2009 12:08 PM
тАО01-22-2009 12:08 PM
Re: Connecting a MSL 6060 directly to server
Of course you need to configure the drivers into the kernel, but you also need to configure the library.
Point your browser to the NSR IP address (default is DHCP - name is router) and create a mapping. Without you don't see anything on fibre channel.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
Point your browser to the NSR IP address (default is DHCP - name is router) and create a mapping. Without you don't see anything on fibre channel.
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-22-2009 02:51 PM
тАО01-22-2009 02:51 PM
Re: Connecting a MSL 6060 directly to server
Hello.
Sujit, Torsten, thanks for your advice.
I found the solution.
What i did was connect thru console and did.
1. Perf. configuration
2. Fiber channel config
3. Port mode, was in N_PORT MODE and I changed it to HARD AL_PA mode.
This solved the problem I now can see library.
Thanks a lot for your time and help.
This server had the library drivers already installed.
Sujit, Torsten, thanks for your advice.
I found the solution.
What i did was connect thru console and did.
1. Perf. configuration
2. Fiber channel config
3. Port mode, was in N_PORT MODE and I changed it to HARD AL_PA mode.
This solved the problem I now can see library.
Thanks a lot for your time and help.
This server had the library drivers already installed.
Knowledge is power.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP