- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- DAT 40I recently has continuous cyclic redundancy ...
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2002 10:07 AM
тАО11-05-2002 10:07 AM
DAT 40I recently has continuous cyclic redundancy check errors
Robert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2002 10:26 AM
тАО11-05-2002 10:26 AM
Re: DAT 40I recently has continuous cyclic redundancy check errors
cleaning tape should be used after every 5 full backups or after 20 tape pulling hours.
Install HP Library and Tape Tools from http://www.hp.com/cposupport/information_storage/support_doc/lpg50128.html , run tests, update firmware etc.
If you see these errors reported for the tape, then drive may be bad, if errors are for drive or SCSI bus, then either drive or something on the bus is bad.
Try replacing SCSI cable and terminator(s), disconnecting all devices from the bus except DAT40i. Try drive in the other machine
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2002 10:53 AM
тАО11-05-2002 10:53 AM
Re: DAT 40I recently has continuous cyclic redundancy check errors
Robert
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2002 11:19 AM
тАО11-05-2002 11:19 AM
Re: DAT 40I recently has continuous cyclic redundancy check errors
Good news, warranty seems to be 3 years.
http://www.hp.com/products1/storage/products/tapebackup/dds_dat_drives/dds4_dat40/warranty.html
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-05-2002 11:26 AM
тАО11-05-2002 11:26 AM
Re: DAT 40I recently has continuous cyclic redundancy check errors
The best way to check drive is to connect it to known good machine and try backup there using, for example, NT backup.
Eugeny