- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- DLT VS80 SCSI settings
StoreEver Tape Storage
1753563
Members
5729
Online
108796
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2003 06:28 AM
04-01-2003 06:28 AM
DLT VS80 SCSI settings
Using IBM xSeries 225 server (with integrated LSI 1030 SCSI adapter) there is a problem with HP Surestore DLT VS80 internal tapedrive. The LSI1030 uses default SCSI settings for DLT VS80, which probably are to high for a tape drive.
So I have to manually adjust following settings in SCSI setup:
MT/Sec (320/160/80/40/20/10/5)
Data With (16/8)
Disconnect (Yes/No)
SCSI Timeout (default=10)
Queue Tags (Yes/No)
Does anyone know what would be the correct settings?
So I have to manually adjust following settings in SCSI setup:
MT/Sec (320/160/80/40/20/10/5)
Data With (16/8)
Disconnect (Yes/No)
SCSI Timeout (default=10)
Queue Tags (Yes/No)
Does anyone know what would be the correct settings?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
04-01-2003 07:17 AM
04-01-2003 07:17 AM
Re: DLT VS80 SCSI settings
See http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=lpg50056&locale=en_US&prodSeriesId=63898&prodTypeId=12169
Speed = I believe 40 will be enough;
Width = 16 bits (but depends on cable and card);
Disconnect = should be Yes. It's SCSI specification, and I guess it's present in SCSI-2 protocol;
Timeout = leave as it is. If there will be problems try to increase to, let's say, 30 seconds (you know drive may take some time to rewind :o) )
Queue Tags = no idea, sorry.
BTW, VS80 is a Benchmark DLT1 drive
Eugeny
Speed = I believe 40 will be enough;
Width = 16 bits (but depends on cable and card);
Disconnect = should be Yes. It's SCSI specification, and I guess it's present in SCSI-2 protocol;
Timeout = leave as it is. If there will be problems try to increase to, let's say, 30 seconds (you know drive may take some time to rewind :o) )
Queue Tags = no idea, sorry.
BTW, VS80 is a Benchmark DLT1 drive
Eugeny
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP