- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: ESL 9595 SDLT 320 Recalibration
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 03:38 AM
тАО09-20-2007 03:38 AM
is there a way to re-calibrate SDLT drives (through HP LTT or command view TL) as after having replaced 2 drives they still generates read/write errors ?
Rgds
Steph
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 06:27 PM
тАО09-20-2007 06:27 PM
SolutionProbably you have some bad tape in the library
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 06:49 PM
тАО09-20-2007 06:49 PM
Re: ESL 9595 SDLT 320 Recalibration
Regarding ESL calibration, can this be done from elsewhere than the control panel ? (remotely : HP LLT or command view TL, Thanks and regards.
Steph
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 07:51 PM
тАО09-20-2007 07:51 PM
Re: ESL 9595 SDLT 320 Recalibration
if the library is not able to load the cartridge in the tape drive, then this may be due to one of these cause:
- the drive itself is not well seated, or the drive is out of place,reseat it and run the library calibration from the front panel of the lib will solve this.
- you are loading a wrong cartridge ( LTO in a SDLT)
- you are loading a cartridge that is up-side down
if the library is able to load the cartridge in the tape, but not able to write it, the cause may be you have loaded a DLT cartridge in the SDLT drive.
if you create a support ticket whith the cartridge loaded in the tape, and attach it here I can have a look, may be the answer is there
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 08:15 PM
тАО09-20-2007 08:15 PM
Re: ESL 9595 SDLT 320 Recalibration
let's say it in other words :
ESL 9595 with 5 SDLTs - SDLT 2 and 4 fail to write to any tape. These drives have been replaced recently. There's no issue with the robotics (cartridges are correctly loaded from slots to SDLT drives then unloaded from SDLTs to slots). When loaded in the SDLT drive, no writing is possible. No possibility to have a wrong tape as the same tape is usable on another SDLT. My question is : before requesting a new SDLT replacement I want to be sure I can't do more. You're talking about "library calibration from the front panel", and this is exactly the original question : can it be run remotely ?(through command view TL or HP LTT). I'm located in France, the ESL is in UK.
Thanks and regards
Steph
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 08:25 PM
тАО09-20-2007 08:25 PM
Re: ESL 9595 SDLT 320 Recalibration
In your case I think that this test will not solve the problem, because it is a pure mechanical calibration of the stepper motors of the robot.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 09:04 PM
тАО09-20-2007 09:04 PM
Re: ESL 9595 SDLT 320 Recalibration
this is the answer !
Thanks. This thread is closed. Have a nice day
Steph
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2007 09:05 PM
тАО09-20-2007 09:05 PM