- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Fault code: 2009 (Soft) Door Open
StoreEver Tape Storage
1752808
Members
5784
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2006 06:50 AM
тАО06-20-2006 06:50 AM
Fault code: 2009 (Soft) Door Open
Fault code: 2009 (Soft) Door Open
Both of the doors are actually CLOSED!
I've tried just about every possible way to remove this error including powering down the server and tape device but it still appears. I searched the IT Resource Center and found what the error referes to:
2009
Door Open
(status only)
(Door is forced open or door sensor failed.)
Invalid user initiated operation. Select parameters correctly and try again.
Make sure door(s) are closed.
Press Enter to clear the message
None of the other options are working in the console so I'm wondering if anyone can provide me some direction for resolving this?
ANY responses are appreciated. Is there a way to manually open the door ? Perhaps I can tighten the alignment screw once I can get the door open ?
Both of the doors are actually CLOSED!
I've tried just about every possible way to remove this error including powering down the server and tape device but it still appears. I searched the IT Resource Center and found what the error referes to:
2009
Door Open
(status only)
(Door is forced open or door sensor failed.)
Invalid user initiated operation. Select parameters correctly and try again.
Make sure door(s) are closed.
Press Enter to clear the message
None of the other options are working in the console so I'm wondering if anyone can provide me some direction for resolving this?
ANY responses are appreciated. Is there a way to manually open the door ? Perhaps I can tighten the alignment screw once I can get the door open ?
3 REPLIES 3
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2006 04:41 PM
тАО06-20-2006 04:41 PM
Re: Fault code: 2009 (Soft) Door Open
Tim,
Which library is this?
Which library is this?
If helpful, provide points!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2006 11:39 PM
тАО06-20-2006 11:39 PM
Re: Fault code: 2009 (Soft) Door Open
Tim,
On a lot of tape libraries I have used, there is a "pin" hole on the front of the doors to manually open the doors. Hope yours does too!
Regards,
JASH
On a lot of tape libraries I have used, there is a "pin" hole on the front of the doors to manually open the doors. Hope yours does too!
Regards,
JASH
If I can, I will!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-21-2006 12:28 AM
тАО06-21-2006 12:28 AM
Re: Fault code: 2009 (Soft) Door Open
The unit is an MSL5000. Fortunately, I was able to get the door open. Just as I have read in other threads - the alignment screw was way off. I aligned by comparing the other door and the storage system seems to be working fine now.
Thanks all !
Tim
Thanks all !
Tim
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP