- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Fault code: 2009 (Soft) error on MSL5000...
StoreEver Tape Storage
1748198
Members
2699
Online
108759
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-25-2005 05:55 AM
тАО07-25-2005 05:55 AM
Fault code: 2009 (Soft) error on MSL5000...
I clicked the Magazine Access button located in the console panel to remove some tapes and received this error after closing the door:
Fault code: 2009 (Soft) Door Open
I've tried just about every possible way to remove this error including powering down the server and tape device but it still appears. I searched the IT Resource Center and found what the error referes to:
2009
Door Open
(status only)
(Door is forced open or door sensor failed.)
Invalid user initiated operation. Select parameters correctly and try again.
Make sure door(s) are closed.
Press Enter to clear the message
None of the other options are working in the console so I'm wondering if anyone can provide me some direction for resolving this?
ANY responses are appreciated.
Fault code: 2009 (Soft) Door Open
I've tried just about every possible way to remove this error including powering down the server and tape device but it still appears. I searched the IT Resource Center and found what the error referes to:
2009
Door Open
(status only)
(Door is forced open or door sensor failed.)
Invalid user initiated operation. Select parameters correctly and try again.
Make sure door(s) are closed.
Press Enter to clear the message
None of the other options are working in the console so I'm wondering if anyone can provide me some direction for resolving this?
ANY responses are appreciated.
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-30-2005 07:22 PM
тАО07-30-2005 07:22 PM
Re: Fault code: 2009 (Soft) error on MSL5000...
Some times when the door of the library is unfortunately closed , the hook which is attached to this door is become slightly shifted and unaligned, then the sensor inside the library give you this message,
to fix this problem, you can adjust the hook alignment by the screw attached with it, you have to do this job carefully and not to tight too much, and better to compare it with the other door.
Good luck..
to fix this problem, you can adjust the hook alignment by the screw attached with it, you have to do this job carefully and not to tight too much, and better to compare it with the other door.
Good luck..
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-20-2006 09:40 AM
тАО06-20-2006 09:40 AM
Re: Fault code: 2009 (Soft) error on MSL5000...
hi;
when you power down the device, doors should release themselves, so you could open them manually.
when you power down the device, doors should release themselves, so you could open them manually.
Computers have lots of memory but no imagination
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP