- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- HP EML103 Library Status Unknown?
StoreEver Tape Storage
1752409
Members
5630
Online
108788
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-19-2010 07:03 AM
10-19-2010 07:03 AM
HP EML103 Library Status Unknown?
Hi there,
we have a HP EML103 Library which seems to have a problem. When I start the library the picker won't move and the library shows unknown (instead of operational), no error messages.
Does anyone know what to do?
we have a HP EML103 Library which seems to have a problem. When I start the library the picker won't move and the library shows unknown (instead of operational), no error messages.
Does anyone know what to do?
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
10-20-2010 11:58 AM
10-20-2010 11:58 AM
Re: HP EML103 Library Status Unknown?
Hello,
A couple things to check...
Are you sure you have removed the shipping restraints (both of them)?
Is the Interface Manager board connected to the RLC (robotic library controller board) via an Ethernet cable?
Does the "Fault" LED stay flashing on the RLC board? If so, verify the IM card is alive and that you can login to the IM board via telnet/ssh.
Is the OCP responsive? Can you navigate around? If so, see which component is lsited as RED in the component status area. If the OCP is not responsive at all, double check the RLC and IM are communicating with each other over the network (again the Eth cable connection is important).
A couple things to check...
Are you sure you have removed the shipping restraints (both of them)?
Is the Interface Manager board connected to the RLC (robotic library controller board) via an Ethernet cable?
Does the "Fault" LED stay flashing on the RLC board? If so, verify the IM card is alive and that you can login to the IM board via telnet/ssh.
Is the OCP responsive? Can you navigate around? If so, see which component is lsited as RED in the component status area. If the OCP is not responsive at all, double check the RLC and IM are communicating with each other over the network (again the Eth cable connection is important).
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP