- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: HP_LTT.exe application error
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-13-2003 11:42 AM
тАО01-13-2003 11:42 AM
HP_LTT.exe application error
"The diagnostic functions are operating in restricted mode. Some functions may be disabled or limited while opereating in restricted mode.
"The restricted mode is entered if either the Product ID is not properly recognised, or if the device operates in 'boot code' and requires a firmware update"
If I OK this message I get a Dr Watson's message...
"An application error has occored and an application error log is being generated.
HP_LTT.exe
Exception: (0x06d7363), Address: 0x77f1d479"
I am running NT4 Server with SP6a.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-13-2003 12:38 PM
тАО01-13-2003 12:38 PM
Re: HP_LTT.exe application error
very very interesting. I see this problem first time. Could you please go to SCSI card bios and get:
a) inquiry strings for both autochanger and drive;
b) firmware levels of both;
c) any other info you may consider interesting/useful.
I know there's HP email address where to route LTT issues. I will try to find it, but you please dig into SCSI bios.
In addition please try using LTT in either NT miniport or ASPI mode. Will it work?
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2003 03:37 AM
тАО01-14-2003 03:37 AM
Re: HP_LTT.exe application error
Firmware = H107
The problem occurs when I try using NT miniport, ASPI mode is not supported.
Karl
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2003 03:46 AM
тАО01-14-2003 03:46 AM
Re: HP_LTT.exe application error
Eugeny
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО01-14-2003 05:29 AM
тАО01-14-2003 05:29 AM
Re: HP_LTT.exe application error
ASPI should be supported on NT4, may require an additional installation step though - during the installation of LTT the installation of the ASPI drivers is an optional component which is deselected by default.
Either re-run the LTT install, or un-install and then re-install LTT. During the installation click the ASPI component. Be advised though that installing ASPI most likely will require you to reboot the system at the conclusion of the install - so you may want to coordinate the time of installation.
If the problem continues to occur, please e-mail the LTT status report which should be generated in case of such a failure to ltt_team@hp.com for analysis.