- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: HP-UX doesn't see tape drives
StoreEver Tape Storage
1753614
Members
6120
Online
108797
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-17-2010 07:48 AM
тАО09-17-2010 07:48 AM
HP-UX doesn't see tape drives
Greetings,
I have IA HP-UX 11.31 with 3 HBA - one dual port and another single, Cisco MDS SAN switch and EML103e with 3 FC tape drives and I wonder why does second port on first HBA couldn't see any devices though I definitely done proper zoning and configuration on EML side... I tried to restart the ports on switch, either host and library but this gave no effect... Below is the output of fcmsutil command:
/ # fcmsutil /dev/fcd1 get remote all
Target N_Port_id is = 0x650300
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x500110a0005a5be2
Target Node World Wide Name = 0x500110a0005a5be0
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : 8800 RO_Bitmap: 3
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800
Target N_Port_id is = 0x650000
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x100000e00244038d
Target Node World Wide Name = 0x100000e00204038d
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : c800 RO_Bitmap: fe
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800
Target N_Port_id is = INVALID
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x500110a0005a5bdf
Target Node World Wide Name = 0x500110a0005a5bdd
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : 8800 RO_Bitmap: 3
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800
I tried to do insf, but with no effect
Any ideas and comments are greatly appreciated
I have IA HP-UX 11.31 with 3 HBA - one dual port and another single, Cisco MDS SAN switch and EML103e with 3 FC tape drives and I wonder why does second port on first HBA couldn't see any devices though I definitely done proper zoning and configuration on EML side... I tried to restart the ports on switch, either host and library but this gave no effect... Below is the output of fcmsutil command:
/ # fcmsutil /dev/fcd1 get remote all
Target N_Port_id is = 0x650300
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x500110a0005a5be2
Target Node World Wide Name = 0x500110a0005a5be0
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : 8800 RO_Bitmap: 3
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800
Target N_Port_id is = 0x650000
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x100000e00244038d
Target Node World Wide Name = 0x100000e00204038d
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : c800 RO_Bitmap: fe
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800
Target N_Port_id is = INVALID
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x500110a0005a5bdf
Target Node World Wide Name = 0x500110a0005a5bdd
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : 8800 RO_Bitmap: 3
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800
I tried to do insf, but with no effect
Any ideas and comments are greatly appreciated
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-19-2010 10:04 PM
тАО09-19-2010 10:04 PM
Re: HP-UX doesn't see tape drives
Try to check with command view TL if security is enabled and adjust if needed.
"stape" driver loaded?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
"stape" driver loaded?
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-20-2010 12:52 AM
тАО09-20-2010 12:52 AM
Re: HP-UX doesn't see tape drives
Thanks for the reply.
Here is the information about driver:
/ #kcmodule -v
Module stape (1.0)
Description Legacy SCSI Tape Driver for 11.31
Timestamp Thu Feb 15 18:31:32 2007 [45D4D134]
State static (best state)
State at Next Boot static (best state)
Capable static unused
Depends On module estape:0.0.0
interface HPUX_11_31_PERF:1.0
And here is information about ports WWNs:
/ # fcmsutil /dev/fcd0 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D7
N_Port Node World Wide Name = 0x5001438004bd5581
N_Port Port World Wide Name = 0x5001438004bd5580
Switch Port World Wide Name = 0x2002000dece7c740
Switch Node World Wide Name = 0x2064000dece7c741
/ # fcmsutil /dev/fcd1 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D7
N_Port Node World Wide Name = 0x5001438004bd5583
N_Port Port World Wide Name = 0x5001438004bd5582
Switch Port World Wide Name = 0x2003000dece4dc40
Switch Node World Wide Name = 0x2065000dece4dc41
/ # fcmsutil /dev/fcd2 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D6
N_Port Node World Wide Name = 0x5001438007d18197
N_Port Port World Wide Name = 0x5001438007d18196
Switch Port World Wide Name = 0x2001000dece7c740
Switch Node World Wide Name = 0x2064000dece7c741
At last, CVTL Host Access configuration is attached.
I rebooted the library today morning, but nothing has changed so far...
Here is the information about driver:
/ #kcmodule -v
Module stape (1.0)
Description Legacy SCSI Tape Driver for 11.31
Timestamp Thu Feb 15 18:31:32 2007 [45D4D134]
State static (best state)
State at Next Boot static (best state)
Capable static unused
Depends On module estape:0.0.0
interface HPUX_11_31_PERF:1.0
And here is information about ports WWNs:
/ # fcmsutil /dev/fcd0 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D7
N_Port Node World Wide Name = 0x5001438004bd5581
N_Port Port World Wide Name = 0x5001438004bd5580
Switch Port World Wide Name = 0x2002000dece7c740
Switch Node World Wide Name = 0x2064000dece7c741
/ # fcmsutil /dev/fcd1 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D7
N_Port Node World Wide Name = 0x5001438004bd5583
N_Port Port World Wide Name = 0x5001438004bd5582
Switch Port World Wide Name = 0x2003000dece4dc40
Switch Node World Wide Name = 0x2065000dece4dc41
/ # fcmsutil /dev/fcd2 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D6
N_Port Node World Wide Name = 0x5001438007d18197
N_Port Port World Wide Name = 0x5001438007d18196
Switch Port World Wide Name = 0x2001000dece7c740
Switch Node World Wide Name = 0x2064000dece7c741
At last, CVTL Host Access configuration is attached.
I rebooted the library today morning, but nothing has changed so far...
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP