HP-UX doesn't see tape drives

[ArtemTr]

Greetings,

I have IA HP-UX 11.31 with 3 HBA - one dual port and another single, Cisco MDS SAN switch and EML103e with 3 FC tape drives and I wonder why does second port on first HBA couldn't see any devices though I definitely done proper zoning and configuration on EML side... I tried to restart the ports on switch, either host and library but this gave no effect... Below is the output of fcmsutil command:

/ # fcmsutil /dev/fcd1 get remote all
Target N_Port_id is = 0x650300
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x500110a0005a5be2
Target Node World Wide Name = 0x500110a0005a5be0
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : 8800 RO_Bitmap: 3
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800

Target N_Port_id is = 0x650000
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x100000e00244038d
Target Node World Wide Name = 0x100000e00204038d
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : c800 RO_Bitmap: fe
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800

Target N_Port_id is = INVALID
Target state = DSM_UNOPENED
Symbolic Port Name =
Symbolic Node Name =
Port Type = N_PORT
FCP-2 Support = YES
Target Port World Wide Name = 0x500110a0005a5bdf
Target Node World Wide Name = 0x500110a0005a5bdd
Common Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Common Features : 8800 RO_Bitmap: 3
Total Conseq: ff
Class 3 Service parameters (all values shown in hex):
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Open Sequences/Exchg: 1 Conseq: ff
Recipient Control Flags: 0 Rxsz: 800

I tried to do insf, but with no effect
Any ideas and comments are greatly appreciated

[Torsten.]

Try to check with command view TL if security is enabled and adjust if needed.
"stape" driver loaded?

[ArtemTr]

Thanks for the reply.

Here is the information about driver:

/ #kcmodule -v
Module stape (1.0)
Description Legacy SCSI Tape Driver for 11.31
Timestamp Thu Feb 15 18:31:32 2007 [45D4D134]
State static (best state)
State at Next Boot static (best state)
Capable static unused
Depends On module estape:0.0.0
interface HPUX_11_31_PERF:1.0

And here is information about ports WWNs:
/ # fcmsutil /dev/fcd0 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D7
N_Port Node World Wide Name = 0x5001438004bd5581
N_Port Port World Wide Name = 0x5001438004bd5580
Switch Port World Wide Name = 0x2002000dece7c740
Switch Node World Wide Name = 0x2064000dece7c741

/ # fcmsutil /dev/fcd1 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D7
N_Port Node World Wide Name = 0x5001438004bd5583
N_Port Port World Wide Name = 0x5001438004bd5582
Switch Port World Wide Name = 0x2003000dece4dc40
Switch Node World Wide Name = 0x2065000dece4dc41

/ # fcmsutil /dev/fcd2 | egrep 'ID|Wide Name'
Vendor ID is = 0x1077
Device ID is = 0x2422
PCI Sub-system Vendor ID is = 0x103C
PCI Sub-system ID is = 0x12D6
N_Port Node World Wide Name = 0x5001438007d18197
N_Port Port World Wide Name = 0x5001438007d18196
Switch Port World Wide Name = 0x2001000dece7c740
Switch Node World Wide Name = 0x2064000dece7c741

At last, CVTL Host Access configuration is attached.

I rebooted the library today morning, but nothing has changed so far...