- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- MSL2024 Close Mailslot not resolved!
StoreEver Tape Storage
1752719
Members
5768
Online
108789
Solutions
Forums
Categories
Company
Local Language
юдл
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
юдл
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО09-30-2010 05:58 AM
тАО09-30-2010 05:58 AM
MSL2024 Close Mailslot not resolved!
Hello,
I have the same issue as several other posters and have done the same tasks trying to resolve the issue. I have the current firmware, clean prisms, no dust bunnies (was clean when I opened the case) and no error codes besides close mailslot. I went thru the same process to get here. First the display stated I had an ├в incompatible magazine├в . It is the one it came with three years ago that has 1 mailslot(two hand holes). Then I updated the firmware at which time I got the ├в close mailslot├в If I enable the mailslot it says I have three mailslots, then when I disable the mailslot in configuration slot 9, 5 and 1 are ├в no access├в I tried to put a washer on the sled in hopes that there was wear causing the LED's to not alighn with the prisms. I have restored factory defaults and restored from a configuration file. I have included a trace dump. Any help would be GREATLY appreciated!
I have the same issue as several other posters and have done the same tasks trying to resolve the issue. I have the current firmware, clean prisms, no dust bunnies (was clean when I opened the case) and no error codes besides close mailslot. I went thru the same process to get here. First the display stated I had an ├в incompatible magazine├в . It is the one it came with three years ago that has 1 mailslot(two hand holes). Then I updated the firmware at which time I got the ├в close mailslot├в If I enable the mailslot it says I have three mailslots, then when I disable the mailslot in configuration slot 9, 5 and 1 are ├в no access├в I tried to put a washer on the sled in hopes that there was wear causing the LED's to not alighn with the prisms. I have restored factory defaults and restored from a configuration file. I have included a trace dump. Any help would be GREATLY appreciated!
2 REPLIES 2
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-01-2010 08:23 AM
тАО10-01-2010 08:23 AM
Re: MSL2024 Close Mailslot not resolved!
just seeing the slot 2 got a lot of retry,
and you have the library in sequence mode instead of random
out of that, could be a magazine defect, did you try to run tests from LTT?
and you have the library in sequence mode instead of random
out of that, could be a magazine defect, did you try to run tests from LTT?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО10-01-2010 08:25 AM
тАО10-01-2010 08:25 AM
Re: MSL2024 Close Mailslot not resolved!
and it looks like there is no load port enabled
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP