- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- MSL6000 with Ultrium 3 Tape Firmware Problems
StoreEver Tape Storage
1752782
Members
6160
Online
108789
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-23-2009 03:54 AM
06-23-2009 03:54 AM
MSL6000 with Ultrium 3 Tape Firmware Problems
Hi there
I've got a MSL6000 Library with 2 Ultrium 3 Tape Drive's in it. I was trying to Upgrade my Firmware to G65W from G63.. On the First drive which I tried it worked flawlessly... but on the Second Drive, I wen't to the Firmware Tab and the Library and Tape Tools 4.7 just crashed and since then I can't access the Drive anymore.. It's not even listet...
Can please anybody help me? I can give you Access to my Server, if you need!
Thanks and Regards
Tom
I've got a MSL6000 Library with 2 Ultrium 3 Tape Drive's in it. I was trying to Upgrade my Firmware to G65W from G63.. On the First drive which I tried it worked flawlessly... but on the Second Drive, I wen't to the Firmware Tab and the Library and Tape Tools 4.7 just crashed and since then I can't access the Drive anymore.. It's not even listet...
Can please anybody help me? I can give you Access to my Server, if you need!
Thanks and Regards
Tom
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
06-23-2009 06:49 PM
06-23-2009 06:49 PM
Re: MSL6000 with Ultrium 3 Tape Firmware Problems
Hi,
If the drive is not getting detected at all then you might want to try the following steps:-
a) Disconnect the drive and connect it back.
b) Check if it gets detected on the Front Panel OCP.
c) If it gets detected on the library, then we can check on the L&TT or the host end as well and upgrade the firmware again.
If not then I would suggest a replacement.
Regards,
Sunny
If the drive is not getting detected at all then you might want to try the following steps:-
a) Disconnect the drive and connect it back.
b) Check if it gets detected on the Front Panel OCP.
c) If it gets detected on the library, then we can check on the L&TT or the host end as well and upgrade the firmware again.
If not then I would suggest a replacement.
Regards,
Sunny
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP