- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Modell C1537A no dokuments
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-22-2000 04:19 AM - last edited on тАО09-02-2014 01:59 AM by Maiko-I
тАО02-22-2000 04:19 AM - last edited on тАО09-02-2014 01:59 AM by Maiko-I
Modell C1537A no dokuments
I can't find any dokuments about this internal tape drive. It's a DDS3 12/24GB
drive. But I didn't get any dokumentation about the jumpers. I have many
trouble to install this drive under Windows NT 4.0 SP 6a.
I can see the installed driver, but the Colorado Backup Software II Version 7.0
can't use the tape drive. I don't know why.
P.S. This thread has been moevd from General to Tape Libraries and Drives. - Hp Forum Moderator
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-29-2000 03:47 AM
тАО02-29-2000 03:47 AM
Re: Modell C1537A no dokuments
support group that supports that software for sure on this,but I believe that
software won't work with the Server version of NT.
As viewed from the back of the tape drive, the pin sets over the power
connector are set up as follows.
Sets as viewed from the left
? ? ? ? ? ?? ?? ???? ?? ??
?? 1 2 3 4 5
set 1 Termination power ]] ]] ]] ]] ]
sets 2,3,4 SCSI address pins.
set 5 (only 1 jumper) No connection
To set the address to 1, pin set 4 would be jumpered
To set the address to 5, pin set 2 and 4 would be jumpered.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-29-2000 11:19 AM
тАО02-29-2000 11:19 AM
Re: Modell C1537A no dokuments
At the moment I use a Win NT Workstation, but I will change it to a Server.
The backside Jumpers are only for the address, but what's about the small
switches on the top of the drive ? Could be that I switched it to the wrong
posistion, because I thought it would be the address.
Can you send me, the right switch position ?
Thanks a lot
Michael Lawrence
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-06-2000 03:32 AM
тАО03-06-2000 03:32 AM
Re: Modell C1537A no dokuments
information is needed to determine the exact functions. There are many
functions of those switches and HP has shipped many different versions
depending on customer need.
We need more exact model number information from the mechanism along with
firmware if possible.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-06-2000 03:28 PM
тАО03-06-2000 03:28 PM
Re: Modell C1537A no dokuments
now I found the problem. I had trouble between my streamer and my scanner.
After disconnect the scanner, the streamer works.
So I don't need the switch positions any more. Thank's a lot.
I have heard that a scanner makes very often problems on a SCSI-Bus. I think I
will buy now a USB-Scanner.
It's easier to handle.
Sincerely
Michael Lawrence