- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Need advice on ESL712 errors
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-20-2009 05:18 AM
тАО11-20-2009 05:18 AM
Hi all.
I need some advice concerning the following :
ESL indicates :
6U CARD CAGE FAN :
Card cage 12V Warning (out of threshold) ACTUAL : 11V (it should be between 11.4-12.6
Card cage 3.3v Inoperative no actual value , state CRITICAL
card cage bottom enclosure fan (RPM) NO ACTUAL VALUE , STATE CRITICAL
card cage bottom power supply fan (RPM) NO ACTUAL VALUE , STATE CRITICAL
card cage top enclosure fan (RPM) NO ACTUAL VALUE , STATE CRITICAL
---------------------------
Alle the fans in the 6U cage are working FINE (the double 90x90 fan works fine).
I even replaced the 2 psu's one by one in the 6 U top cage, still have the same problem.
I see 2 problems, the voltage that is too low and inoperative for the 3.3v.
And the FAN RPM's that can't be seen/measured (maybe related to the 1st problem.)
My question, what advice can you give me on how to proceed.
I was thinking about changing the whole 6U TOP CAGE cause there's some electronics in it, but it's soo expensive I want to be sure :p (we don't have a maint contract with HP).
thx for the advice
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2009 11:21 AM
тАО11-23-2009 11:21 AM
Re: Need advice on ESL712 errors
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-23-2009 03:00 PM
тАО11-23-2009 03:00 PM
Re: Need advice on ESL712 errors
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО11-27-2009 06:11 AM
тАО11-27-2009 06:11 AM
Re: Need advice on ESL712 errors
Hi guys,
thx for all the help sofar.
I checked the serial cabling.. You can't plug it in the wrong way in the 6U card cage.
It enters the robotic controller in the bottom of the ESL712, same thing, you can't plug it in the wrong way.
I checked the whole cable it's OK .
But it could be somethings wrong in that robotics controller too of course ?
Before starting to order parts I would like to find something that gives me more certainty, the parts cost a lot of money :p
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 06:19 AM
тАО12-02-2009 06:19 AM
Re: Need advice on ESL712 errors
Ok I got my new 6U top card cage.
Did a full poweroff, installed it (it contained 2 new psu's & new double 90x90 fans), everything booted fine but I still see all previous errors in the webinterface...
My question, how can I reset all the counters/errors on the tape lib ?
btw I found no problem with the serial cable, you insert it in the wrong way...
cheers
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 08:08 AM
тАО12-02-2009 08:08 AM
Re: Need advice on ESL712 errors
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 11:53 PM
тАО12-02-2009 11:53 PM
Re: Need advice on ESL712 errors
For the sake of clarification I took 2 screenshots of the hp commandview tl :
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-02-2009 11:53 PM
тАО12-02-2009 11:53 PM
Re: Need advice on ESL712 errors
2nd screenshot
Help is appreciated !
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2009 07:22 AM
тАО12-03-2009 07:22 AM
Re: Need advice on ESL712 errors
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО12-03-2009 09:23 AM
тАО12-03-2009 09:23 AM
Solution