- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Re: Replacement of the drive in MSL6030
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-15-2008 04:26 AM
тАО05-15-2008 04:26 AM
Replacement of the drive in MSL6030
FW library and drives is max updated.
Drive with ID 1 fell out and was replaced new one.
Now drive with ID 2 works normally and new drive with ID 1 doesnтАЩt write.
In DP 6 we have:
"Cannot write to device ([1117] The request could not be performed because of an I/O device error." This isn't DP error - we know.
This drive don't pass-through тАЭDrive Conectivity testтАЭ in HP StorageWorks Library and Tape Tools. But all physical connection is normal state. In recommendations we need check the configuration of our SCSI Bus. How can I do that?
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-15-2008 07:44 AM
тАО05-15-2008 07:44 AM
Re: Replacement of the drive in MSL6030
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c00659626&jumpid=reg_R1002_USEN
Notice terminators are on the drive and not in the library controller.
what does HP L&TT says? you can load a support ticket here.
Did you have the NSR to discover for the new drive, and checked the mapping is correct?
You can as well swap both drives to see if the problems follows drive #1 or stays in the bay/cabling/NSR Port. Or swap NSR SCSI port to isolate the problem.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-18-2008 10:17 PM
тАО05-18-2008 10:17 PM
Re: Replacement of the drive in MSL6030
http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c00659626&jumpid=reg_R1002_USEN
Notice terminators are on the drive and not in the library controller."
Terminator was on the controller, in compliance with your recommendation now.
Nothing change.
2)"what does HP L&TT says? you can load a support ticket here."
HP L&TT says what "Drive Connectivity test failed". (Please verify that the physical connection between your host and the drive is operational).
3)"Please check the configuration of your SCSI Bus, proper termination, proper installation of all required drivers."
All checked, no problem found.
4)"Did you have the NSR to discover for the new drive, and checked the mapping is correct?"
Yes, and there is all good.
5)"You can as well swap both drives to see if the problems follows drive #1 or stays in the bay/cabling/NSR Port. Or swap NSR SCSI port to isolate the problem."
The problems follows drive #1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-19-2008 07:51 AM
тАО05-19-2008 07:51 AM
Re: Replacement of the drive in MSL6030
see attach.
Thanks.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-20-2008 02:07 PM
тАО05-20-2008 02:07 PM
Re: Replacement of the drive in MSL6030
Seems like the drive is not responding.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО05-20-2008 09:39 PM
тАО05-20-2008 09:39 PM
Re: Replacement of the drive in MSL6030
Although on all other devises drive #2 visible without problem (on router, on hosts with DP6, in library and so on).
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО06-05-2008 03:33 AM
тАО06-05-2008 03:33 AM