- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- SAN and tape library
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 12:10 AM
тАО03-02-2011 12:10 AM
SAN and tape library
I have MSL6000 and DL-380 Server, last week we installed Brocade 8/24 switch and want to connect all devices using this switch.
I am able to view MSL6000 on server when directly connected to server. but when i connect it via brocade switch it is not visible to server.
Even without zone and with zone its not visible to server.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 12:19 AM
тАО03-02-2011 12:19 AM
Re: SAN and tape library
Hope this helps!
Regards
Torsten.
__________________________________________________
There are only 10 types of people in the world -
those who understand binary, and those who don't.
__________________________________________________
No support by private messages. Please ask the forum!
If you feel this was helpful please click the KUDOS! thumb below!
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 12:35 AM
тАО03-02-2011 12:35 AM
Re: SAN and tape library
Like Torsten said, you must do mapping inside NSR between SCSI addresses and WWN.
Otherwise, you test that from Brocade you see both devices correctly.
Regards, Jorge
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 01:34 AM
тАО03-02-2011 01:34 AM
Re: SAN and tape library
I dont know how to map. In Discovery i am getting the following
FC PORT 0 DEVICES
There are no devices attached to this port at this time.
SCSI BUS 0 DEVICES
Bus Target ID LUN ID Device Type State Map Count Device Description
0 0 0 CHGR UP 0 HP MSL6000 Series 0520
0 1 0 TAPE UP 0 HP Ultrium 2-SCSI F59W
SCSI BUS 1 DEVICES
There are no devices attached to this port at this time.
VIRTUAL DEVICES
Type State Map Cnt LUN ID Device Description Serial No.
CTLR UP 0 0 HP NS E1200-160
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-02-2011 03:31 AM
тАО03-02-2011 03:31 AM
Re: SAN and tape library
Here are a good manual to do:
http://h20000.www2.hp.com/bc/docs/support/SupportManual/c00637161/c00637161.pdf?jumpid=reg_R1002_USEN
Regards, Jorge