- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- SDT-9000 Problem
StoreEver Tape Storage
1753731
Members
4761
Online
108799
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-10-2005 05:59 PM
08-10-2005 05:59 PM
SDT-9000 Problem
I have an SDT-9000 DDS3 drive in a Windows 2003 server. The server runs Backup Exec v9.1.
I have replaced the drive twice now but contine to have the same problem.
Problem 1 - When I put a new tape in for the nights backup, it ejects straight away as if it never even fully inserts.
Problem 2 - I ran the HP Storageworks Library and Tape Tools v3.5 SR2 diags on the drive and it came up with a failure during the Media Analysis test:
Drive reported unrevovered I/O error condition test phase cannot proceed. I/O excpetion (sense key 3 Sense code 0x1100 - Unrecovred read error). SCSI cmd I/O @ 3/0.3.0 space
Problem 3 - During the read/write test, the drive continually ejected the cleaning tape (100+ times) and I had to cancel the test.
I don't think the problem is the drive, but then again???
All help greatly appreciated.
I have replaced the drive twice now but contine to have the same problem.
Problem 1 - When I put a new tape in for the nights backup, it ejects straight away as if it never even fully inserts.
Problem 2 - I ran the HP Storageworks Library and Tape Tools v3.5 SR2 diags on the drive and it came up with a failure during the Media Analysis test:
Drive reported unrevovered I/O error condition test phase cannot proceed. I/O excpetion (sense key 3 Sense code 0x1100 - Unrecovred read error). SCSI cmd I/O @ 3/0.3.0 space
Problem 3 - During the read/write test, the drive continually ejected the cleaning tape (100+ times) and I had to cancel the test.
I don't think the problem is the drive, but then again???
All help greatly appreciated.
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
08-16-2005 06:04 PM
08-16-2005 06:04 PM
Re: SDT-9000 Problem
Problem 1- be sure to format/inizialize the new tape with you backup sw before to use it, or it will be ejected because of unknown format
problem 2-If the media is not formatted and ther is no data on it, you cannot perform a media analysis test because this test read data on tape.
problem 3- if ltt fail read/write test, and ask for cleaning cartridge, this is because the head of the drive is not able to write /read on the specific tape.
Or you got a bad drive or you get bad tapes. You can run the media validation test(That is a non destructive test) on old written tapes to identify if the problem is with new tapes or with new drive
marino
problem 2-If the media is not formatted and ther is no data on it, you cannot perform a media analysis test because this test read data on tape.
problem 3- if ltt fail read/write test, and ask for cleaning cartridge, this is because the head of the drive is not able to write /read on the specific tape.
Or you got a bad drive or you get bad tapes. You can run the media validation test(That is a non destructive test) on old written tapes to identify if the problem is with new tapes or with new drive
marino
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP