- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- Server Free Backup MSL6060 with NSR E1200
Categories
Company
Local Language
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Forums
Discussions
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Community
Resources
Forums
Blogs
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-26-2004 02:12 AM
тАО03-26-2004 02:12 AM
For backup we use Data Protector 5.1 and a MSL6060 with two Ultrium LTO2 and a NSR E1200 embedded. The MSL is connectend to the Fibre.
Backup via LAN is working fine, but i like to backup server free via Fiber Channel.
No the problem i have is, that on the NSR E1200 i can't configure this. On the Web Gui there is under System, Active Fabric ServerFree Backup Disabled. I can't enable this. In the manual i read something from service mode restricted access?!
Then i think to upgrade all firmwares. TapeLibrary and Drives are no Problem, but i can't upgrade the firmware of the NSR. Current Firmware is 0104 and new is 530b.
the upgrade process stops with sense code 0x3a00.
I use hp storage works library and tape tools for upgrade. also i look for firmware upgrade via telnet/web gui from the nsr, but the menu is not available, again service mode restricted access?!
My primary question is what must i configure for server free backup?
when i have to upgrade the firmware of the nsr, how?
Thanks for Help and Greetings from Switzerland
Solved! Go to Solution.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-26-2004 05:14 AM
тАО03-26-2004 05:14 AM
SolutionThere is two backup concepts that often are confused as both use SAN-attached drives.
- Serverless backup.
- Lanfree backup.
Lanfree backup is rather similar to local connected drives. The backup data flow from the client to the tape drive via SAN. All (SAN attached) clients can write direct to the tape drives and som kind of device locking is needed to prevent more then one client writing to a drive at the same time. To use Lanfree backup in DP you just need to configure Library drives for each client and adress the backup objects for every client to its own logical drive.
Serverless backup is different, the data is sent direct from the disk system to the tape drive (via SAN and the Storage Router/Data Mover). Serverless backup is a more complex concept and very hardware and software dependent. The support for Serverless backup in DP 5.1 is also rather limited.
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО03-29-2004 01:19 AM
тАО03-29-2004 01:19 AM
Re: Server Free Backup MSL6060 with NSR E1200
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО07-03-2006 11:51 PM
тАО07-03-2006 11:51 PM
Re: Server Free Backup MSL6060 with NSR E1200
I am also facing the same problem.Can you share what u did to get the same working. I also want to do a server free backup. I have a msa1k with embeded SAN switch and msl 6030 tape library with NSR E1200-160.I am also able to take lan free but serverfree is not working.backup s/w used is CA arcserv 11.1
Thanks in advance
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
тАО02-16-2007 03:46 AM
тАО02-16-2007 03:46 AM
Re: Server Free Backup MSL6060 with NSR E1200
I will need some kinf of license to perform a lan free backup ?
tks in advance