- Community Home
- >
- Storage
- >
- Data Protection and Retention
- >
- StoreEver Tape Storage
- >
- StorageWorks 3U Rack-Mount Kit SCSI ID
StoreEver Tape Storage
1752579
Members
3063
Online
108788
Solutions
Forums
Categories
Company
Local Language
back
Forums
Discussions
Forums
- Data Protection and Retention
- Entry Storage Systems
- Legacy
- Midrange and Enterprise Storage
- Storage Networking
- HPE Nimble Storage
Discussions
Discussions
Discussions
Forums
Discussions
back
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
- BladeSystem Infrastructure and Application Solutions
- Appliance Servers
- Alpha Servers
- BackOffice Products
- Internet Products
- HPE 9000 and HPE e3000 Servers
- Networking
- Netservers
- Secure OS Software for Linux
- Server Management (Insight Manager 7)
- Windows Server 2003
- Operating System - Tru64 Unix
- ProLiant Deployment and Provisioning
- Linux-Based Community / Regional
- Microsoft System Center Integration
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Discussion Boards
Blogs
Information
Community
Resources
Community Language
Language
Forums
Blogs
Topic Options
- Subscribe to RSS Feed
- Mark Topic as New
- Mark Topic as Read
- Float this Topic for Current User
- Bookmark
- Subscribe
- Printer Friendly Page
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-14-2004 08:50 PM
07-14-2004 08:50 PM
StorageWorks 3U Rack-Mount Kit SCSI ID
I am currently evaluating the Compaq Storageworks 3U Rack-Mount kit. Below is the instructions for setting SCSI ID.
I am quite confused here...
Do we set the SCSI ID via cable connection or on the tape drive?
---------------------------------------------
The default SCSI ID for each tape drive depends on the cable configuration used in the
storage enclosure. If there is one tape drive per SCSI cable, the default is 0. For two
tape drives per SCSI cable, the default for the top tape drive is 1 and the default for the
bottom tape drive is 0.
Before setting the SCSI ID, be sure the SCSI ID complies with the following:
â ¢ Each SCSI device on the same SCSI bus must have a unique SCSI ID.
â ¢ If the tape drives' SCSI IDs need to be reassigned, do not duplicate SCSI IDs.
â ¢ Do not use SCSI ID 7 because it is reserved for the controller.
To set or change the SCSI ID of a tape drive, refer to your tape driv
I am quite confused here...
Do we set the SCSI ID via cable connection or on the tape drive?
---------------------------------------------
The default SCSI ID for each tape drive depends on the cable configuration used in the
storage enclosure. If there is one tape drive per SCSI cable, the default is 0. For two
tape drives per SCSI cable, the default for the top tape drive is 1 and the default for the
bottom tape drive is 0.
Before setting the SCSI ID, be sure the SCSI ID complies with the following:
â ¢ Each SCSI device on the same SCSI bus must have a unique SCSI ID.
â ¢ If the tape drives' SCSI IDs need to be reassigned, do not duplicate SCSI IDs.
â ¢ Do not use SCSI ID 7 because it is reserved for the controller.
To set or change the SCSI ID of a tape drive, refer to your tape driv
All Your Bases Are Belong To Us!
1 REPLY 1
- Mark as New
- Bookmark
- Subscribe
- Mute
- Subscribe to RSS Feed
- Permalink
- Report Inappropriate Content
07-14-2004 09:05 PM
07-14-2004 09:05 PM
Re: StorageWorks 3U Rack-Mount Kit SCSI ID
You set it on the tape drive, so you do need the user manual for it, too.
.
The opinions expressed above are the personal opinions of the authors, not of Hewlett Packard Enterprise. By using this site, you accept the Terms of Use and Rules of Participation.
News and Events
Support
© Copyright 2024 Hewlett Packard Enterprise Development LP